DIY: rolling your own fenders.
#1
DIY: rolling your own fenders.
This is for those who are thinking of rolling their own fenders. I am not responsible if you do anything wrong. This is just a guide.
Fender rolling costs about 100-150 around here which is a rip off for something so simple. I just went to home depot and bought a
$1.50 sch 40 2" PCV pipe.
Saved myself $98.50 for other cool mods![Smilie](https://g35driver.com/forums/images/smilies/smile.gif)
Here is the stock fender.
![Name: stockunrolled.jpg
Views: 1421
Size: 70.1 KB](https://g35driver.com/forums/attachments/brakes-suspension-diy/228110d1501885145-diy-rolling-your-own-fenders-stockunrolled.jpg)
I started by jacking car enough for the PCV pipe to fit between the tire and the fender to bend the lip. I then heated up the fender with a hair dryer until it was warm. I started from the left side and pushed/rolled the pcv pipe towards the middle with the hair dryer following the pipe. I did the same starting from the right. Don't try to bend the lip with just one pass. I did serveral passes to make sure the paint didn't crack
![Name: pcvpipehairdryer.jpg
Views: 5263
Size: 56.2 KB](https://g35driver.com/forums/attachments/brakes-suspension-diy/228111d1501885145-diy-rolling-your-own-fenders-pcvpipehairdryer.jpg)
Keep it at an angle and roll like seen below to bent the lip even more.
![Name: pcvpipe2.jpg
Views: 1788
Size: 72.5 KB](https://g35driver.com/forums/attachments/brakes-suspension-diy/228112d1501885145-diy-rolling-your-own-fenders-pcvpipe2.jpg)
done!
![Name: done.jpg
Views: 1262
Size: 45.7 KB](https://g35driver.com/forums/attachments/brakes-suspension-diy/228113d1501885145-diy-rolling-your-own-fenders-done.jpg)
looks good?
![Name: done2.jpg
Views: 1269
Size: 62.7 KB](https://g35driver.com/forums/attachments/brakes-suspension-diy/228114d1501885145-diy-rolling-your-own-fenders-done2.jpg)
It's easier with two people.. one person holding the dryer and the other angling, pushing and rolling the pcv pipe. It was quite hard holding the dryer and rolling at the same time.
goodluck
It was my first time rolling a fender too haha
for more info go to:
http://forums.audiworld.com/s4/msgs/1745791.phtml
Fender rolling costs about 100-150 around here which is a rip off for something so simple. I just went to home depot and bought a
$1.50 sch 40 2" PCV pipe.
Saved myself $98.50 for other cool mods
![Smilie](https://g35driver.com/forums/images/smilies/smile.gif)
Here is the stock fender.
![Name: stockunrolled.jpg
Views: 1421
Size: 70.1 KB](https://g35driver.com/forums/attachments/brakes-suspension-diy/228110d1501885145-diy-rolling-your-own-fenders-stockunrolled.jpg)
I started by jacking car enough for the PCV pipe to fit between the tire and the fender to bend the lip. I then heated up the fender with a hair dryer until it was warm. I started from the left side and pushed/rolled the pcv pipe towards the middle with the hair dryer following the pipe. I did the same starting from the right. Don't try to bend the lip with just one pass. I did serveral passes to make sure the paint didn't crack
![Name: pcvpipehairdryer.jpg
Views: 5263
Size: 56.2 KB](https://g35driver.com/forums/attachments/brakes-suspension-diy/228111d1501885145-diy-rolling-your-own-fenders-pcvpipehairdryer.jpg)
Keep it at an angle and roll like seen below to bent the lip even more.
![Name: pcvpipe2.jpg
Views: 1788
Size: 72.5 KB](https://g35driver.com/forums/attachments/brakes-suspension-diy/228112d1501885145-diy-rolling-your-own-fenders-pcvpipe2.jpg)
done!
![Name: done.jpg
Views: 1262
Size: 45.7 KB](https://g35driver.com/forums/attachments/brakes-suspension-diy/228113d1501885145-diy-rolling-your-own-fenders-done.jpg)
looks good?
![Smilie](https://g35driver.com/forums/images/smilies/smile.gif)
![Name: done2.jpg
Views: 1269
Size: 62.7 KB](https://g35driver.com/forums/attachments/brakes-suspension-diy/228114d1501885145-diy-rolling-your-own-fenders-done2.jpg)
It's easier with two people.. one person holding the dryer and the other angling, pushing and rolling the pcv pipe. It was quite hard holding the dryer and rolling at the same time.
goodluck
![Smilie](https://g35driver.com/forums/images/smilies/smile.gif)
for more info go to:
http://forums.audiworld.com/s4/msgs/1745791.phtml
#2
#5
Registered User
iTrader: (1)
Join Date: Feb 2006
Location: 626
Posts: 1,154
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by drsifu1
you r a legend...the DIY master.
all it really takes is something like this write-up to get others like myself to do it. now the question...how much to rent that PVC pipe?![Smilie](https://g35driver.com/forums/images/smilies/smile.gif)
must have come from your honda days
thanks david.
all it really takes is something like this write-up to get others like myself to do it. now the question...how much to rent that PVC pipe?
![Smilie](https://g35driver.com/forums/images/smilies/smile.gif)
must have come from your honda days
thanks david.
#7
Trending Topics
#8
Originally Posted by redlude97
Can you get a full roll with that method though, some people might need more clearance
you would probably have to use something that won't bend. (i.e. baseball bat) the pcv pipe was bending from the heat and the amount of force being pushed against the pipe. You could probably use a solid wooden cylinder.
as for returning... i'm sure you can't return something that look like this.....
hahah
Last edited by accordfreak; 01-30-2007 at 01:39 AM.
#10
#13