View Poll Results: What BBK do you have? (please add to thread)
Racing Brake
9
1.93%
Brembo
94
20.13%
StopTech
49
10.49%
Endless
10
2.14%
Project Mu
9
1.93%
Rotora
33
7.07%
Megan
4
0.86%
Wilwood
17
3.64%
Ap Racing (Stillen)
20
4.28%
I have stock brakes
222
47.54%
Voters: 467. You may not vote on this poll
What BBK and wheels do you have?
#31
#32
2004 G35X, hope this qualifies as a BBK.
G35 Coupe Brembos
Front
4-piston with racing brake slotted 2 piece rotors (12.8" x 1.2") 15 lbs.
fits SSR GT7 rims, 19x8.5, 40 offset (plenty of clearance)
Rear
2-piston with racing brake slotted 2 piece rotors (12.7" x 0.9") 16 lbs.
fits SSR GT7 rims, 19x8.5, 40 offset
G35 Coupe Brembos
Front
4-piston with racing brake slotted 2 piece rotors (12.8" x 1.2") 15 lbs.
fits SSR GT7 rims, 19x8.5, 40 offset (plenty of clearance)
Rear
2-piston with racing brake slotted 2 piece rotors (12.7" x 0.9") 16 lbs.
fits SSR GT7 rims, 19x8.5, 40 offset
Last edited by qbturbo; 05-07-2008 at 10:32 PM.
#33
FRONT
Racing Brake
4-Pot 13"
1. Zenetti Five 20x8.5 +40
2. Sevas S-55 20x8.5 +40 (just clears)
3. 5-Zigen FN01R-C 17x8 +43
Brembo
1.
StopTech
1. 14.1" 4 pod Amistad 19" Rotino 19X8.5 +37
2. 13" 4 pot, FN01R-C 17x9 +35 (track), otherwise OEM rims
3. 13" ST-40, FN01R-C 17x8 +35 (3-4mm of clearance)
4. 13" ST-40, Stock Mitsu EVO 8 Enkei 17x8 +38 (plenty of clearance)
5. 18x8*OEM; 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60 [F] & 4-Pot ST-45[R], (2-3mm clearance on rear is close, but works - 3-4mm front is Ok)
6. 18x9 SSR GT2-H (track) 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60[F] & 4-Pot ST45[R] calipers (plenty of clearance F&R)
Endless
1. Endless 6 pod 14.1" Amistad 19" Rotino 19X8.5 +37
Project Mu
1.
Rotora
1. 6-pot 355mmx32mm Volk GT-7 19"x8.5" +23 high disk
2. 6-pot 355mmx32mm Junction Produce Scara Japan 19"x9.5" +23 high disk (needed 3mm spacer)
3. 6-pot 355mmx32mm Volk SF-Challenge 19x9.5 +28
4. 12-pot 380mmx34mm iForged Aero 20x8.5 +40 (sedan)
5.12 pot 380 mm HRE 944 20x9.5
6. 6-pot 355mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
Wilwood
1. 14.1" 6 piston Wilwood Stock 17" Sedan wheels
2. 13" x 1.37 rotors, SL-6 Wilwood, 17X8 5Zigen wheels
3. AZ Z Car kit, 13" 4-pot FSL, 5Zigen FNO1R-C 17x8 +43
4. 14" x 1.25" Wilwood factory drilled & slotted rotors/ Wilwood SL6 Calipers (Red) with Rays Eng. Coupe 19s
5. 14" Wilwood factory drilled and sloted rotors with 6 piston SL6 calipers same as candlestickpark but in black. 18 inch Ray's Engineering 350Z track (18x8 +30 offset)
Ksport
1.
AP Racing (Stillen)
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2. Beware: '03 Coupe 18x8*OEM wheels; P/N AP3700 (front) 6-Pot w/14.25" rotors too tight to trust w/< 1mm -2mm! P/N AP3750 w/ 4-Pot is ok on rear. Stillen says should be OK on front, measure and decide 4 u-sef!
REAR:
Racing Brake
OEM with 13" rotor
1. Zenetti Five 20x10 +43
2. Sevas S-55 20x10 +40
Brembo
1.
StopTech
1. 13" 2-pot, FN01R-C 17x9 +35 (track), OEM otherwise
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip (does not fit without 10mm spacer!!!)
3. 13" 2-pot, iForged Essen 19x9.5 +45 and sometimes OEM sport 18's
4. 4-pot 355mmx32mm Anceltion SPSIX Revo 20"x10.5" +27 high disk
Endless
1.
Project Mu
1.
Rotora
1. 4-pot 355mmx32mm Volk GT-7 19"x9.5" +24 standard disk
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip
3. 4-pot 380mm x 34mm Maya GR5 20x10.5 +29
4. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (also Volk GT-C 20x9.5 +47)
5. 4-pot 355mm x 32mm Volk SF-Challenge 19x10.5 +23
6. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (sedan)
7. 4 pot 380 mm HRE 944 20x11 (might change to 20x10.5) G37
8. 4-pot 332mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
Wilwood
1. 13" 4 piston Wilwood factory kit with 18" Ray's Engineering 350Z Track 18's (18x8.5 +33 offset)
Ksport
1.
AP Racing (Stillen)
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc
Racing Brake
4-Pot 13"
1. Zenetti Five 20x8.5 +40
2. Sevas S-55 20x8.5 +40 (just clears)
3. 5-Zigen FN01R-C 17x8 +43
Brembo
1.
StopTech
1. 14.1" 4 pod Amistad 19" Rotino 19X8.5 +37
2. 13" 4 pot, FN01R-C 17x9 +35 (track), otherwise OEM rims
3. 13" ST-40, FN01R-C 17x8 +35 (3-4mm of clearance)
4. 13" ST-40, Stock Mitsu EVO 8 Enkei 17x8 +38 (plenty of clearance)
5. 18x8*OEM; 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60 [F] & 4-Pot ST-45[R], (2-3mm clearance on rear is close, but works - 3-4mm front is Ok)
6. 18x9 SSR GT2-H (track) 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60[F] & 4-Pot ST45[R] calipers (plenty of clearance F&R)
Endless
1. Endless 6 pod 14.1" Amistad 19" Rotino 19X8.5 +37
Project Mu
1.
Rotora
1. 6-pot 355mmx32mm Volk GT-7 19"x8.5" +23 high disk
2. 6-pot 355mmx32mm Junction Produce Scara Japan 19"x9.5" +23 high disk (needed 3mm spacer)
3. 6-pot 355mmx32mm Volk SF-Challenge 19x9.5 +28
4. 12-pot 380mmx34mm iForged Aero 20x8.5 +40 (sedan)
5.12 pot 380 mm HRE 944 20x9.5
6. 6-pot 355mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
Wilwood
1. 14.1" 6 piston Wilwood Stock 17" Sedan wheels
2. 13" x 1.37 rotors, SL-6 Wilwood, 17X8 5Zigen wheels
3. AZ Z Car kit, 13" 4-pot FSL, 5Zigen FNO1R-C 17x8 +43
4. 14" x 1.25" Wilwood factory drilled & slotted rotors/ Wilwood SL6 Calipers (Red) with Rays Eng. Coupe 19s
5. 14" Wilwood factory drilled and sloted rotors with 6 piston SL6 calipers same as candlestickpark but in black. 18 inch Ray's Engineering 350Z track (18x8 +30 offset)
Ksport
1.
AP Racing (Stillen)
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2. Beware: '03 Coupe 18x8*OEM wheels; P/N AP3700 (front) 6-Pot w/14.25" rotors too tight to trust w/< 1mm -2mm! P/N AP3750 w/ 4-Pot is ok on rear. Stillen says should be OK on front, measure and decide 4 u-sef!
REAR:
Racing Brake
OEM with 13" rotor
1. Zenetti Five 20x10 +43
2. Sevas S-55 20x10 +40
Brembo
1.
StopTech
1. 13" 2-pot, FN01R-C 17x9 +35 (track), OEM otherwise
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip (does not fit without 10mm spacer!!!)
3. 13" 2-pot, iForged Essen 19x9.5 +45 and sometimes OEM sport 18's
4. 4-pot 355mmx32mm Anceltion SPSIX Revo 20"x10.5" +27 high disk
Endless
1.
Project Mu
1.
Rotora
1. 4-pot 355mmx32mm Volk GT-7 19"x9.5" +24 standard disk
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip
3. 4-pot 380mm x 34mm Maya GR5 20x10.5 +29
4. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (also Volk GT-C 20x9.5 +47)
5. 4-pot 355mm x 32mm Volk SF-Challenge 19x10.5 +23
6. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (sedan)
7. 4 pot 380 mm HRE 944 20x11 (might change to 20x10.5) G37
8. 4-pot 332mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
Wilwood
1. 13" 4 piston Wilwood factory kit with 18" Ray's Engineering 350Z Track 18's (18x8.5 +33 offset)
Ksport
1.
AP Racing (Stillen)
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc
#35
#37
FRONT
Racing Brake
4-Pot 13"
1. Zenetti Five 20x8.5 +40
2. Sevas S-55 20x8.5 +40 (just clears)
3. 5-Zigen FN01R-C 17x8 +43
Brembo
1.
StopTech
1. 14.1" 4 pod Amistad 19" Rotino 19X8.5 +37
2. 13" 4 pot, FN01R-C 17x9 +35 (track), otherwise OEM rims
3. 13" ST-40, FN01R-C 17x8 +35 (3-4mm of clearance)
4. 13" ST-40, Stock Mitsu EVO 8 Enkei 17x8 +38 (plenty of clearance)
5. 18x8*OEM; 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60 [F] & 4-Pot ST-45[R], (2-3mm clearance on rear is close, but works - 3-4mm front is Ok)
6. 18x9 SSR GT2-H (track) 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60[F] & 4-Pot ST45[R] calipers (plenty of clearance F&R)
Endless
1. Endless 6 pod 14.1" Amistad 19" Rotino 19X8.5 +37
Project Mu
1.
Rotora
1. 6-pot 355mmx32mm Volk GT-7 19"x8.5" +23 high disk
2. 6-pot 355mmx32mm Junction Produce Scara Japan 19"x9.5" +23 high disk (needed 3mm spacer)
3. 6-pot 355mmx32mm Volk SF-Challenge 19x9.5 +28
4. 12-pot 380mmx34mm iForged Aero 20x8.5 +40 (sedan)
5.12 pot 380 mm HRE 944 20x9.5
6. 6-pot 355mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2.14.25" / 6 piston with 19" Seva S-Stars w/ 10MM Spacers (daily) & 18" MB Weapons (track)
Wilwood
1. 14.1" 6 piston Wilwood Stock 17" Sedan wheels
2. 13" x 1.37 rotors, SL-6 Wilwood, 17X8 5Zigen wheels
3. AZ Z Car kit, 13" 4-pot FSL, 5Zigen FNO1R-C 17x8 +43
4. 14" x 1.25" Wilwood factory drilled & slotted rotors/ Wilwood SL6 Calipers (Red) with Rays Eng. Coupe 19s
5. 14" Wilwood factory drilled and sloted rotors with 6 piston SL6 calipers same as candlestickpark but in black. 18 inch Ray's Engineering 350Z track (18x8 +30 offset)
Ksport
1.
AP Racing (Stillen)
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2. Beware: '03 Coupe 18x8*OEM wheels; P/N AP3700 (front) 6-Pot w/14.25" rotors too tight to trust w/< 1mm -2mm! P/N AP3750 w/ 4-Pot is ok on rear. Stillen says should be OK on front, measure and decide 4 u-sef!
REAR:
Racing Brake
OEM with 13" rotor
1. Zenetti Five 20x10 +43
2. Sevas S-55 20x10 +40
Brembo
1.
StopTech
1. 13" 2-pot, FN01R-C 17x9 +35 (track), OEM otherwise
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip (does not fit without 10mm spacer!!!)
3. 13" 2-pot, iForged Essen 19x9.5 +45 and sometimes OEM sport 18's
4. 4-pot 355mmx32mm Anceltion SPSIX Revo 20"x10.5" +27 high disk
Endless
1.
Project Mu
1.
Rotora
1. 4-pot 355mmx32mm Volk GT-7 19"x9.5" +24 standard disk
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip
3. 4-pot 380mm x 34mm Maya GR5 20x10.5 +29
4. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (also Volk GT-C 20x9.5 +47)
5. 4-pot 355mm x 32mm Volk SF-Challenge 19x10.5 +23
6. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (sedan)
7. 4 pot 380 mm HRE 944 20x11 (might change to 20x10.5) G37
8. 4-pot 332mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
1. 13.5" 4 piston with 19" Seva S-Stars (daily) & 18" MB Weapons (track)
Wilwood
1. 13" 4 piston Wilwood factory kit with 18" Ray's Engineering 350Z Track 18's (18x8.5 +33 offset)
Ksport
1.
AP Racing (Stillen)
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc
Racing Brake
4-Pot 13"
1. Zenetti Five 20x8.5 +40
2. Sevas S-55 20x8.5 +40 (just clears)
3. 5-Zigen FN01R-C 17x8 +43
Brembo
1.
StopTech
1. 14.1" 4 pod Amistad 19" Rotino 19X8.5 +37
2. 13" 4 pot, FN01R-C 17x9 +35 (track), otherwise OEM rims
3. 13" ST-40, FN01R-C 17x8 +35 (3-4mm of clearance)
4. 13" ST-40, Stock Mitsu EVO 8 Enkei 17x8 +38 (plenty of clearance)
5. 18x8*OEM; 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60 [F] & 4-Pot ST-45[R], (2-3mm clearance on rear is close, but works - 3-4mm front is Ok)
6. 18x9 SSR GT2-H (track) 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60[F] & 4-Pot ST45[R] calipers (plenty of clearance F&R)
Endless
1. Endless 6 pod 14.1" Amistad 19" Rotino 19X8.5 +37
Project Mu
1.
Rotora
1. 6-pot 355mmx32mm Volk GT-7 19"x8.5" +23 high disk
2. 6-pot 355mmx32mm Junction Produce Scara Japan 19"x9.5" +23 high disk (needed 3mm spacer)
3. 6-pot 355mmx32mm Volk SF-Challenge 19x9.5 +28
4. 12-pot 380mmx34mm iForged Aero 20x8.5 +40 (sedan)
5.12 pot 380 mm HRE 944 20x9.5
6. 6-pot 355mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2.14.25" / 6 piston with 19" Seva S-Stars w/ 10MM Spacers (daily) & 18" MB Weapons (track)
Wilwood
1. 14.1" 6 piston Wilwood Stock 17" Sedan wheels
2. 13" x 1.37 rotors, SL-6 Wilwood, 17X8 5Zigen wheels
3. AZ Z Car kit, 13" 4-pot FSL, 5Zigen FNO1R-C 17x8 +43
4. 14" x 1.25" Wilwood factory drilled & slotted rotors/ Wilwood SL6 Calipers (Red) with Rays Eng. Coupe 19s
5. 14" Wilwood factory drilled and sloted rotors with 6 piston SL6 calipers same as candlestickpark but in black. 18 inch Ray's Engineering 350Z track (18x8 +30 offset)
Ksport
1.
AP Racing (Stillen)
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2. Beware: '03 Coupe 18x8*OEM wheels; P/N AP3700 (front) 6-Pot w/14.25" rotors too tight to trust w/< 1mm -2mm! P/N AP3750 w/ 4-Pot is ok on rear. Stillen says should be OK on front, measure and decide 4 u-sef!
REAR:
Racing Brake
OEM with 13" rotor
1. Zenetti Five 20x10 +43
2. Sevas S-55 20x10 +40
Brembo
1.
StopTech
1. 13" 2-pot, FN01R-C 17x9 +35 (track), OEM otherwise
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip (does not fit without 10mm spacer!!!)
3. 13" 2-pot, iForged Essen 19x9.5 +45 and sometimes OEM sport 18's
4. 4-pot 355mmx32mm Anceltion SPSIX Revo 20"x10.5" +27 high disk
Endless
1.
Project Mu
1.
Rotora
1. 4-pot 355mmx32mm Volk GT-7 19"x9.5" +24 standard disk
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip
3. 4-pot 380mm x 34mm Maya GR5 20x10.5 +29
4. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (also Volk GT-C 20x9.5 +47)
5. 4-pot 355mm x 32mm Volk SF-Challenge 19x10.5 +23
6. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (sedan)
7. 4 pot 380 mm HRE 944 20x11 (might change to 20x10.5) G37
8. 4-pot 332mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
1. 13.5" 4 piston with 19" Seva S-Stars (daily) & 18" MB Weapons (track)
Wilwood
1. 13" 4 piston Wilwood factory kit with 18" Ray's Engineering 350Z Track 18's (18x8.5 +33 offset)
Ksport
1.
AP Racing (Stillen)
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc
#38
FRONT
Racing Brake
4-Pot 13"
1. Zenetti Five 20x8.5 +40
2. Sevas S-55 20x8.5 +40 (just clears)
3. 5-Zigen FN01R-C 17x8 +43
Brembo
1.
StopTech
1. 14.1" 4 pod Amistad 19" Rotino 19X8.5 +37
2. 13" 4 pot, FN01R-C 17x9 +35 (track), otherwise OEM rims
3. 13" ST-40, FN01R-C 17x8 +35 (3-4mm of clearance)
4. 13" ST-40, Stock Mitsu EVO 8 Enkei 17x8 +38 (plenty of clearance)
5. 18x8*OEM; 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60 [F] & 4-Pot ST-45[R], (2-3mm clearance on rear is close, but works - 3-4mm front is Ok)
6. 18x9 SSR GT2-H (track) 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60[F] & 4-Pot ST45[R] calipers (plenty of clearance F&R)
7. 19x9.5 Volk GTS +17 Gunmetal 332x32 slotted 2 piece ST-40
Endless
1. Endless 6 pod 14.1" Amistad 19" Rotino 19X8.5 +37
Project Mu
1.
Rotora
1. 6-pot 355mmx32mm Volk GT-7 19"x8.5" +23 high disk
2. 6-pot 355mmx32mm Junction Produce Scara Japan 19"x9.5" +23 high disk (needed 3mm spacer)
3. 6-pot 355mmx32mm Volk SF-Challenge 19x9.5 +28
4. 12-pot 380mmx34mm iForged Aero 20x8.5 +40 (sedan)
5.12 pot 380 mm HRE 944 20x9.5
6. 6-pot 355mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2.14.25" / 6 piston with 19" Seva S-Stars w/ 10MM Spacers (daily) & 18" MB Weapons (track)
Wilwood
1. 14.1" 6 piston Wilwood Stock 17" Sedan wheels
2. 13" x 1.37 rotors, SL-6 Wilwood, 17X8 5Zigen wheels
3. AZ Z Car kit, 13" 4-pot FSL, 5Zigen FNO1R-C 17x8 +43
4. 14" x 1.25" Wilwood factory drilled & slotted rotors/ Wilwood SL6 Calipers (Red) with Rays Eng. Coupe 19s
5. 14" Wilwood factory drilled and sloted rotors with 6 piston SL6 calipers same as candlestickpark but in black. 18 inch Ray's Engineering 350Z track (18x8 +30 offset)
Ksport
1.
AP Racing (Stillen)
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2. Beware: '03 Coupe 18x8*OEM wheels; P/N AP3700 (front) 6-Pot w/14.25" rotors too tight to trust w/< 1mm -2mm! P/N AP3750 w/ 4-Pot is ok on rear. Stillen says should be OK on front, measure and decide 4 u-sef!
REAR:
Racing Brake
OEM with 13" rotor
1. Zenetti Five 20x10 +43
2. Sevas S-55 20x10 +40
Brembo
1.
StopTech
1. 13" 2-pot, FN01R-C 17x9 +35 (track), OEM otherwise
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip (does not fit without 10mm spacer!!!)
3. 13" 2-pot, iForged Essen 19x9.5 +45 and sometimes OEM sport 18's
4. 4-pot 355mmx32mm Anceltion SPSIX Revo 20"x10.5" +27 high disk
Endless
1.
Project Mu
1.
Rotora
1. 4-pot 355mmx32mm Volk GT-7 19"x9.5" +24 standard disk
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip
3. 4-pot 380mm x 34mm Maya GR5 20x10.5 +29
4. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (also Volk GT-C 20x9.5 +47)
5. 4-pot 355mm x 32mm Volk SF-Challenge 19x10.5 +23
6. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (sedan)
7. 4 pot 380 mm HRE 944 20x11 (might change to 20x10.5) G37
8. 4-pot 332mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
1. 13.5" 4 piston with 19" Seva S-Stars (daily) & 18" MB Weapons (track)
Wilwood
1. 13" 4 piston Wilwood factory kit with 18" Ray's Engineering 350Z Track 18's (18x8.5 +33 offset)
Ksport
1.
AP Racing (Stillen)
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc
__________________
Racing Brake
4-Pot 13"
1. Zenetti Five 20x8.5 +40
2. Sevas S-55 20x8.5 +40 (just clears)
3. 5-Zigen FN01R-C 17x8 +43
Brembo
1.
StopTech
1. 14.1" 4 pod Amistad 19" Rotino 19X8.5 +37
2. 13" 4 pot, FN01R-C 17x9 +35 (track), otherwise OEM rims
3. 13" ST-40, FN01R-C 17x8 +35 (3-4mm of clearance)
4. 13" ST-40, Stock Mitsu EVO 8 Enkei 17x8 +38 (plenty of clearance)
5. 18x8*OEM; 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60 [F] & 4-Pot ST-45[R], (2-3mm clearance on rear is close, but works - 3-4mm front is Ok)
6. 18x9 SSR GT2-H (track) 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60[F] & 4-Pot ST45[R] calipers (plenty of clearance F&R)
7. 19x9.5 Volk GTS +17 Gunmetal 332x32 slotted 2 piece ST-40
Endless
1. Endless 6 pod 14.1" Amistad 19" Rotino 19X8.5 +37
Project Mu
1.
Rotora
1. 6-pot 355mmx32mm Volk GT-7 19"x8.5" +23 high disk
2. 6-pot 355mmx32mm Junction Produce Scara Japan 19"x9.5" +23 high disk (needed 3mm spacer)
3. 6-pot 355mmx32mm Volk SF-Challenge 19x9.5 +28
4. 12-pot 380mmx34mm iForged Aero 20x8.5 +40 (sedan)
5.12 pot 380 mm HRE 944 20x9.5
6. 6-pot 355mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2.14.25" / 6 piston with 19" Seva S-Stars w/ 10MM Spacers (daily) & 18" MB Weapons (track)
Wilwood
1. 14.1" 6 piston Wilwood Stock 17" Sedan wheels
2. 13" x 1.37 rotors, SL-6 Wilwood, 17X8 5Zigen wheels
3. AZ Z Car kit, 13" 4-pot FSL, 5Zigen FNO1R-C 17x8 +43
4. 14" x 1.25" Wilwood factory drilled & slotted rotors/ Wilwood SL6 Calipers (Red) with Rays Eng. Coupe 19s
5. 14" Wilwood factory drilled and sloted rotors with 6 piston SL6 calipers same as candlestickpark but in black. 18 inch Ray's Engineering 350Z track (18x8 +30 offset)
Ksport
1.
AP Racing (Stillen)
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2. Beware: '03 Coupe 18x8*OEM wheels; P/N AP3700 (front) 6-Pot w/14.25" rotors too tight to trust w/< 1mm -2mm! P/N AP3750 w/ 4-Pot is ok on rear. Stillen says should be OK on front, measure and decide 4 u-sef!
REAR:
Racing Brake
OEM with 13" rotor
1. Zenetti Five 20x10 +43
2. Sevas S-55 20x10 +40
Brembo
1.
StopTech
1. 13" 2-pot, FN01R-C 17x9 +35 (track), OEM otherwise
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip (does not fit without 10mm spacer!!!)
3. 13" 2-pot, iForged Essen 19x9.5 +45 and sometimes OEM sport 18's
4. 4-pot 355mmx32mm Anceltion SPSIX Revo 20"x10.5" +27 high disk
Endless
1.
Project Mu
1.
Rotora
1. 4-pot 355mmx32mm Volk GT-7 19"x9.5" +24 standard disk
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip
3. 4-pot 380mm x 34mm Maya GR5 20x10.5 +29
4. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (also Volk GT-C 20x9.5 +47)
5. 4-pot 355mm x 32mm Volk SF-Challenge 19x10.5 +23
6. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (sedan)
7. 4 pot 380 mm HRE 944 20x11 (might change to 20x10.5) G37
8. 4-pot 332mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
1. 13.5" 4 piston with 19" Seva S-Stars (daily) & 18" MB Weapons (track)
Wilwood
1. 13" 4 piston Wilwood factory kit with 18" Ray's Engineering 350Z Track 18's (18x8.5 +33 offset)
Ksport
1.
AP Racing (Stillen)
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc
__________________
Last edited by vq35dedriver; 05-24-2009 at 09:19 PM.
#39
FRONT
Racing Brake
4-Pot 13"
1. Zenetti Five 20x8.5 +40
2. Sevas S-55 20x8.5 +40 (just clears)
3. 5-Zigen FN01R-C 17x8 +43
Brembo
1.
StopTech
1. 14.1" 4 pod Amistad 19" Rotino 19X8.5 +37
2. 13" 4 pot, FN01R-C 17x9 +35 (track), otherwise OEM rims
3. 13" ST-40, FN01R-C 17x8 +35 (3-4mm of clearance)
4. 13" ST-40, Stock Mitsu EVO 8 Enkei 17x8 +38 (plenty of clearance)
5. 18x8*OEM; 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60 [F] & 4-Pot ST-45[R], (2-3mm clearance on rear is close, but works - 3-4mm front is Ok)
6. 18x9 SSR GT2-H (track) 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60[F] & 4-Pot ST45[R] calipers (plenty of clearance F&R)
7. 19x8.5 Tenzo-R DC-5 Black 332x32 slotted 2 piece ST-40
8. 4-pot ST-40 355mmx32mm, Anceltion SPSIX Revo 20"x9.5" +27 high disk
9. 4-pot ST-40 355mmx32mm, Enkei NT03+M 18"x9.5" +27
Endless
1. Endless 6 pod 14.1" Amistad 19" Rotino 19X8.5 +37
Project Mu
1.
Rotora
1. 6-pot 355mmx32mm Volk GT-7 19"x8.5" +23 high disk
2. 6-pot 355mmx32mm Junction Produce Scara Japan 19"x9.5" +23 high disk (needed 3mm spacer)
3. 6-pot 355mmx32mm Volk SF-Challenge 19x9.5 +28
4. 12-pot 380mmx34mm iForged Aero 20x8.5 +40 (sedan)
5.12 pot 380 mm HRE 944 20x9.5
6. 6-pot 355mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2.14.25" / 6 piston with 19" Seva S-Stars w/ 10MM Spacers (daily) & 18" MB Weapons (track)
Wilwood
1. 14.1" 6 piston Wilwood Stock 17" Sedan wheels
2. 13" x 1.37 rotors, SL-6 Wilwood, 17X8 5Zigen wheels
3. AZ Z Car kit, 13" 4-pot FSL, 5Zigen FNO1R-C 17x8 +43
4. 14" x 1.25" Wilwood factory drilled & slotted rotors/ Wilwood SL6 Calipers (Red) with Rays Eng. Coupe 19s
5. 14" Wilwood factory drilled and sloted rotors with 6 piston SL6 calipers same as candlestickpark but in black. 18 inch Ray's Engineering 350Z track (18x8 +30 offset)
Ksport
1.
AP Racing (Stillen)
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2. Beware: '03 Coupe 18x8*OEM wheels; P/N AP3700 (front) 6-Pot w/14.25" rotors too tight to trust w/< 1mm -2mm! P/N AP3750 w/ 4-Pot is ok on rear. Stillen says should be OK on front, measure and decide 4 u-sef!
REAR:
Racing Brake
OEM with 13" rotor
1. Zenetti Five 20x10 +43
2. Sevas S-55 20x10 +40
Brembo
1.
StopTech
1. 13" 2-pot, FN01R-C 17x9 +35 (track), OEM otherwise
2. 4-pot ST-45 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip (does not fit without 10mm spacer!!!)
3. 13" 2-pot, iForged Essen 19x9.5 +45 and sometimes OEM sport 18's
4. 4-pot ST-45 355mmx32mm Anceltion SPSIX Revo 20"x10.5" +27 high disk
5. 4-pot ST-45 355mmx32mm Enkei NT03+M 18"x10.5" +30
Endless
1.
Project Mu
1.
Rotora
1. 4-pot 355mmx32mm Volk GT-7 19"x9.5" +24 standard disk
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip
3. 4-pot 380mm x 34mm Maya GR5 20x10.5 +29
4. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (also Volk GT-C 20x9.5 +47)
5. 4-pot 355mm x 32mm Volk SF-Challenge 19x10.5 +23
6. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (sedan)
7. 4 pot 380 mm HRE 944 20x11 (might change to 20x10.5) G37
8. 4-pot 332mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
1. 13.5" 4 piston with 19" Seva S-Stars (daily) & 18" MB Weapons (track)
Wilwood
1. 13" 4 piston Wilwood factory kit with 18" Ray's Engineering 350Z Track 18's (18x8.5 +33 offset)
Ksport
1.
AP Racing (Stillen)
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc
__________________[/QUOTE]
Racing Brake
4-Pot 13"
1. Zenetti Five 20x8.5 +40
2. Sevas S-55 20x8.5 +40 (just clears)
3. 5-Zigen FN01R-C 17x8 +43
Brembo
1.
StopTech
1. 14.1" 4 pod Amistad 19" Rotino 19X8.5 +37
2. 13" 4 pot, FN01R-C 17x9 +35 (track), otherwise OEM rims
3. 13" ST-40, FN01R-C 17x8 +35 (3-4mm of clearance)
4. 13" ST-40, Stock Mitsu EVO 8 Enkei 17x8 +38 (plenty of clearance)
5. 18x8*OEM; 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60 [F] & 4-Pot ST-45[R], (2-3mm clearance on rear is close, but works - 3-4mm front is Ok)
6. 18x9 SSR GT2-H (track) 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60[F] & 4-Pot ST45[R] calipers (plenty of clearance F&R)
7. 19x8.5 Tenzo-R DC-5 Black 332x32 slotted 2 piece ST-40
8. 4-pot ST-40 355mmx32mm, Anceltion SPSIX Revo 20"x9.5" +27 high disk
9. 4-pot ST-40 355mmx32mm, Enkei NT03+M 18"x9.5" +27
Endless
1. Endless 6 pod 14.1" Amistad 19" Rotino 19X8.5 +37
Project Mu
1.
Rotora
1. 6-pot 355mmx32mm Volk GT-7 19"x8.5" +23 high disk
2. 6-pot 355mmx32mm Junction Produce Scara Japan 19"x9.5" +23 high disk (needed 3mm spacer)
3. 6-pot 355mmx32mm Volk SF-Challenge 19x9.5 +28
4. 12-pot 380mmx34mm iForged Aero 20x8.5 +40 (sedan)
5.12 pot 380 mm HRE 944 20x9.5
6. 6-pot 355mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2.14.25" / 6 piston with 19" Seva S-Stars w/ 10MM Spacers (daily) & 18" MB Weapons (track)
Wilwood
1. 14.1" 6 piston Wilwood Stock 17" Sedan wheels
2. 13" x 1.37 rotors, SL-6 Wilwood, 17X8 5Zigen wheels
3. AZ Z Car kit, 13" 4-pot FSL, 5Zigen FNO1R-C 17x8 +43
4. 14" x 1.25" Wilwood factory drilled & slotted rotors/ Wilwood SL6 Calipers (Red) with Rays Eng. Coupe 19s
5. 14" Wilwood factory drilled and sloted rotors with 6 piston SL6 calipers same as candlestickpark but in black. 18 inch Ray's Engineering 350Z track (18x8 +30 offset)
Ksport
1.
AP Racing (Stillen)
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2. Beware: '03 Coupe 18x8*OEM wheels; P/N AP3700 (front) 6-Pot w/14.25" rotors too tight to trust w/< 1mm -2mm! P/N AP3750 w/ 4-Pot is ok on rear. Stillen says should be OK on front, measure and decide 4 u-sef!
REAR:
Racing Brake
OEM with 13" rotor
1. Zenetti Five 20x10 +43
2. Sevas S-55 20x10 +40
Brembo
1.
StopTech
1. 13" 2-pot, FN01R-C 17x9 +35 (track), OEM otherwise
2. 4-pot ST-45 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip (does not fit without 10mm spacer!!!)
3. 13" 2-pot, iForged Essen 19x9.5 +45 and sometimes OEM sport 18's
4. 4-pot ST-45 355mmx32mm Anceltion SPSIX Revo 20"x10.5" +27 high disk
5. 4-pot ST-45 355mmx32mm Enkei NT03+M 18"x10.5" +30
Endless
1.
Project Mu
1.
Rotora
1. 4-pot 355mmx32mm Volk GT-7 19"x9.5" +24 standard disk
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip
3. 4-pot 380mm x 34mm Maya GR5 20x10.5 +29
4. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (also Volk GT-C 20x9.5 +47)
5. 4-pot 355mm x 32mm Volk SF-Challenge 19x10.5 +23
6. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (sedan)
7. 4 pot 380 mm HRE 944 20x11 (might change to 20x10.5) G37
8. 4-pot 332mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
1. 13.5" 4 piston with 19" Seva S-Stars (daily) & 18" MB Weapons (track)
Wilwood
1. 13" 4 piston Wilwood factory kit with 18" Ray's Engineering 350Z Track 18's (18x8.5 +33 offset)
Ksport
1.
AP Racing (Stillen)
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc
__________________[/QUOTE]
#42
Added D2 Racing Brakes
FRONT:
Racing Brake
4-Pot 13"
1. Zenetti Five 20x8.5 +40
2. Sevas S-55 20x8.5 +40 (just clears)
3. 5-Zigen FN01R-C 17x8 +43
Brembo
1.
StopTech
1. 14.1" 4 pod Amistad 19" Rotino 19X8.5 +37
2. 13" 4 pot, FN01R-C 17x9 +35 (track), otherwise OEM rims
3. 13" ST-40, FN01R-C 17x8 +35 (3-4mm of clearance)
4. 13" ST-40, Stock Mitsu EVO 8 Enkei 17x8 +38 (plenty of clearance)
5. 18x8*OEM; 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60 [F] & 4-Pot ST-45[R], (2-3mm clearance on rear is close, but works - 3-4mm front is Ok)
6. 18x9 SSR GT2-H (track) 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60[F] & 4-Pot ST45[R] calipers (plenty of clearance F&R)
7. 19x8.5 Tenzo-R DC-5 Black 332x32 slotted 2 piece ST-40
8. 4-pot ST-40 355mmx32mm, Anceltion SPSIX Revo 20"x9.5" +27 high disk
9. 4-pot ST-40 355mmx32mm, Enkei NT03+M 18"x9.5" +27
Endless
1. Endless 6 pod 14.1" Amistad 19" Rotino 19X8.5 +37
Project Mu
1.
Rotora
1. 6-pot 355mmx32mm Volk GT-7 19"x8.5" +23 high disk
2. 6-pot 355mmx32mm Junction Produce Scara Japan 19"x9.5" +23 high disk (needed 3mm spacer)
3. 6-pot 355mmx32mm Volk SF-Challenge 19x9.5 +28
4. 12-pot 380mmx34mm iForged Aero 20x8.5 +40 (sedan)
5.12 pot 380 mm HRE 944 20x9.5
6. 6-pot 355mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2.14.25" / 6 piston with 19" Seva S-Stars w/ 10MM Spacers (daily) & 18" MB Weapons (track)
Wilwood
1. 14.1" 6 piston Wilwood Stock 17" Sedan wheels
2. 13" x 1.37 rotors, SL-6 Wilwood, 17X8 5Zigen wheels
3. AZ Z Car kit, 13" 4-pot FSL, 5Zigen FNO1R-C 17x8 +43
4. 14" x 1.25" Wilwood factory drilled & slotted rotors/ Wilwood SL6 Calipers (Red) with Rays Eng. Coupe 19s
5. 14" Wilwood factory drilled and sloted rotors with 6 piston SL6 calipers same as candlestickpark but in black. 18 inch Ray's Engineering 350Z track (18x8 +30 offset)
Ksport
1.
AP Racing (Stillen)
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2. Beware: '03 Coupe 18x8*OEM wheels; P/N AP3700 (front) 6-Pot w/14.25" rotors too tight to trust w/< 1mm -2mm! P/N AP3750 w/ 4-Pot is ok on rear. Stillen says should be OK on front, measure and decide 4 u-sef!
D2 Racing
1. 356mm / 8 piston with 19x8.5 Volk Racing GT-S (Sedan)
REAR:
Racing Brake
OEM with 13" rotor
1. Zenetti Five 20x10 +43
2. Sevas S-55 20x10 +40
Brembo
1.
StopTech
1. 13" 2-pot, FN01R-C 17x9 +35 (track), OEM otherwise
2. 4-pot ST-45 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip (does not fit without 10mm spacer!!!)
3. 13" 2-pot, iForged Essen 19x9.5 +45 and sometimes OEM sport 18's
4. 4-pot ST-45 355mmx32mm Anceltion SPSIX Revo 20"x10.5" +27 high disk
5. 4-pot ST-45 355mmx32mm Enkei NT03+M 18"x10.5" +30
Endless
1.
Project Mu
1.
Rotora
1. 4-pot 355mmx32mm Volk GT-7 19"x9.5" +24 standard disk
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip
3. 4-pot 380mm x 34mm Maya GR5 20x10.5 +29
4. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (also Volk GT-C 20x9.5 +47)
5. 4-pot 355mm x 32mm Volk SF-Challenge 19x10.5 +23
6. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (sedan)
7. 4 pot 380 mm HRE 944 20x11 (might change to 20x10.5) G37
8. 4-pot 332mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
1. 13.5" 4 piston with 19" Seva S-Stars (daily) & 18" MB Weapons (track)
Wilwood
1. 13" 4 piston Wilwood factory kit with 18" Ray's Engineering 350Z Track 18's (18x8.5 +33 offset)
Ksport
1.
AP Racing (Stillen)
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc
D2 Racing
1. 328mm / 6 piston with 19x9.5 Volk Racing GT-S (Sedan)
Racing Brake
4-Pot 13"
1. Zenetti Five 20x8.5 +40
2. Sevas S-55 20x8.5 +40 (just clears)
3. 5-Zigen FN01R-C 17x8 +43
Brembo
1.
StopTech
1. 14.1" 4 pod Amistad 19" Rotino 19X8.5 +37
2. 13" 4 pot, FN01R-C 17x9 +35 (track), otherwise OEM rims
3. 13" ST-40, FN01R-C 17x8 +35 (3-4mm of clearance)
4. 13" ST-40, Stock Mitsu EVO 8 Enkei 17x8 +38 (plenty of clearance)
5. 18x8*OEM; 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60 [F] & 4-Pot ST-45[R], (2-3mm clearance on rear is close, but works - 3-4mm front is Ok)
6. 18x9 SSR GT2-H (track) 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60[F] & 4-Pot ST45[R] calipers (plenty of clearance F&R)
7. 19x8.5 Tenzo-R DC-5 Black 332x32 slotted 2 piece ST-40
8. 4-pot ST-40 355mmx32mm, Anceltion SPSIX Revo 20"x9.5" +27 high disk
9. 4-pot ST-40 355mmx32mm, Enkei NT03+M 18"x9.5" +27
Endless
1. Endless 6 pod 14.1" Amistad 19" Rotino 19X8.5 +37
Project Mu
1.
Rotora
1. 6-pot 355mmx32mm Volk GT-7 19"x8.5" +23 high disk
2. 6-pot 355mmx32mm Junction Produce Scara Japan 19"x9.5" +23 high disk (needed 3mm spacer)
3. 6-pot 355mmx32mm Volk SF-Challenge 19x9.5 +28
4. 12-pot 380mmx34mm iForged Aero 20x8.5 +40 (sedan)
5.12 pot 380 mm HRE 944 20x9.5
6. 6-pot 355mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2.14.25" / 6 piston with 19" Seva S-Stars w/ 10MM Spacers (daily) & 18" MB Weapons (track)
Wilwood
1. 14.1" 6 piston Wilwood Stock 17" Sedan wheels
2. 13" x 1.37 rotors, SL-6 Wilwood, 17X8 5Zigen wheels
3. AZ Z Car kit, 13" 4-pot FSL, 5Zigen FNO1R-C 17x8 +43
4. 14" x 1.25" Wilwood factory drilled & slotted rotors/ Wilwood SL6 Calipers (Red) with Rays Eng. Coupe 19s
5. 14" Wilwood factory drilled and sloted rotors with 6 piston SL6 calipers same as candlestickpark but in black. 18 inch Ray's Engineering 350Z track (18x8 +30 offset)
Ksport
1.
AP Racing (Stillen)
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2. Beware: '03 Coupe 18x8*OEM wheels; P/N AP3700 (front) 6-Pot w/14.25" rotors too tight to trust w/< 1mm -2mm! P/N AP3750 w/ 4-Pot is ok on rear. Stillen says should be OK on front, measure and decide 4 u-sef!
D2 Racing
1. 356mm / 8 piston with 19x8.5 Volk Racing GT-S (Sedan)
REAR:
Racing Brake
OEM with 13" rotor
1. Zenetti Five 20x10 +43
2. Sevas S-55 20x10 +40
Brembo
1.
StopTech
1. 13" 2-pot, FN01R-C 17x9 +35 (track), OEM otherwise
2. 4-pot ST-45 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip (does not fit without 10mm spacer!!!)
3. 13" 2-pot, iForged Essen 19x9.5 +45 and sometimes OEM sport 18's
4. 4-pot ST-45 355mmx32mm Anceltion SPSIX Revo 20"x10.5" +27 high disk
5. 4-pot ST-45 355mmx32mm Enkei NT03+M 18"x10.5" +30
Endless
1.
Project Mu
1.
Rotora
1. 4-pot 355mmx32mm Volk GT-7 19"x9.5" +24 standard disk
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip
3. 4-pot 380mm x 34mm Maya GR5 20x10.5 +29
4. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (also Volk GT-C 20x9.5 +47)
5. 4-pot 355mm x 32mm Volk SF-Challenge 19x10.5 +23
6. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (sedan)
7. 4 pot 380 mm HRE 944 20x11 (might change to 20x10.5) G37
8. 4-pot 332mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
1. 13.5" 4 piston with 19" Seva S-Stars (daily) & 18" MB Weapons (track)
Wilwood
1. 13" 4 piston Wilwood factory kit with 18" Ray's Engineering 350Z Track 18's (18x8.5 +33 offset)
Ksport
1.
AP Racing (Stillen)
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc
D2 Racing
1. 328mm / 6 piston with 19x9.5 Volk Racing GT-S (Sedan)
#43
#44
Registered User
iTrader: (23)
Join Date: Nov 2007
Location: SoCal
Posts: 3,684
Likes: 0
Received 0 Likes
on
0 Posts
FRONT:
Racing Brake
4-Pot 13"
1. Zenetti Five 20x8.5 +40
2. Sevas S-55 20x8.5 +40 (just clears)
3. 5-Zigen FN01R-C 17x8 +43
Brembo
1.
StopTech
1. 14.1" 4 pod Amistad 19" Rotino 19X8.5 +37
2. 13" 4 pot, FN01R-C 17x9 +35 (track), otherwise OEM rims
3. 13" ST-40, FN01R-C 17x8 +35 (3-4mm of clearance)
4. 13" ST-40, Stock Mitsu EVO 8 Enkei 17x8 +38 (plenty of clearance)
5. 18x8*OEM; 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60 [F] & 4-Pot ST-45[R], (2-3mm clearance on rear is close, but works - 3-4mm front is Ok)
6. 18x9 SSR GT2-H (track) 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60[F] & 4-Pot ST45[R] calipers (plenty of clearance F&R)
7. 19x8.5 Tenzo-R DC-5 Black 332x32 slotted 2 piece ST-40
8. 4-pot ST-40 355mmx32mm, Anceltion SPSIX Revo 20"x9.5" +27 high disk
9. 4-pot ST-40 355mmx32mm, Enkei NT03+M 18"x9.5" +27
10. 4-pot ST-40 355mmx32mm, RacingHart RS521 19x9.0 +26 (Good Clearance)
Endless
1. Endless 6 pod 14.1" Amistad 19" Rotino 19X8.5 +37
Project Mu
1.
Rotora
1. 6-pot 355mmx32mm Volk GT-7 19"x8.5" +23 high disk
2. 6-pot 355mmx32mm Junction Produce Scara Japan 19"x9.5" +23 high disk (needed 3mm spacer)
3. 6-pot 355mmx32mm Volk SF-Challenge 19x9.5 +28
4. 12-pot 380mmx34mm iForged Aero 20x8.5 +40 (sedan)
5.12 pot 380 mm HRE 944 20x9.5
6. 6-pot 355mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2.14.25" / 6 piston with 19" Seva S-Stars w/ 10MM Spacers (daily) & 18" MB Weapons (track)
Wilwood
1. 14.1" 6 piston Wilwood Stock 17" Sedan wheels
2. 13" x 1.37 rotors, SL-6 Wilwood, 17X8 5Zigen wheels
3. AZ Z Car kit, 13" 4-pot FSL, 5Zigen FNO1R-C 17x8 +43
4. 14" x 1.25" Wilwood factory drilled & slotted rotors/ Wilwood SL6 Calipers (Red) with Rays Eng. Coupe 19s
5. 14" Wilwood factory drilled and sloted rotors with 6 piston SL6 calipers same as candlestickpark but in black. 18 inch Ray's Engineering 350Z track (18x8 +30 offset)
Ksport
1.
AP Racing (Stillen)
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2. Beware: '03 Coupe 18x8*OEM wheels; P/N AP3700 (front) 6-Pot w/14.25" rotors too tight to trust w/< 1mm -2mm! P/N AP3750 w/ 4-Pot is ok on rear. Stillen says should be OK on front, measure and decide 4 u-sef!
D2 Racing
1. 356mm / 8 piston with 19x8.5 Volk Racing GT-S (Sedan)
REAR:
Racing Brake
OEM with 13" rotor
1. Zenetti Five 20x10 +43
2. Sevas S-55 20x10 +40
Brembo
1.
StopTech
1. 13" 2-pot, FN01R-C 17x9 +35 (track), OEM otherwise
2. 4-pot ST-45 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip (does not fit without 10mm spacer!!!)
3. 13" 2-pot, iForged Essen 19x9.5 +45 and sometimes OEM sport 18's
4. 4-pot ST-45 355mmx32mm Anceltion SPSIX Revo 20"x10.5" +27 high disk
5. 4-pot ST-45 355mmx32mm Enkei NT03+M 18"x10.5" +30
6. 4-pot ST-45 355mmx32mm, RacingHart RS521 19x10.5 +22 (Barely Clears)
Endless
1.
Project Mu
1.
Rotora
1. 4-pot 355mmx32mm Volk GT-7 19"x9.5" +24 standard disk
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip
3. 4-pot 380mm x 34mm Maya GR5 20x10.5 +29
4. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (also Volk GT-C 20x9.5 +47)
5. 4-pot 355mm x 32mm Volk SF-Challenge 19x10.5 +23
6. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (sedan)
7. 4 pot 380 mm HRE 944 20x11 (might change to 20x10.5) G37
8. 4-pot 332mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
1. 13.5" 4 piston with 19" Seva S-Stars (daily) & 18" MB Weapons (track)
Wilwood
1. 13" 4 piston Wilwood factory kit with 18" Ray's Engineering 350Z Track 18's (18x8.5 +33 offset)
Ksport
1.
AP Racing (Stillen)
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc
D2 Racing
1. 328mm / 6 piston with 19x9.5 Volk Racing GT-S (Sedan)
Racing Brake
4-Pot 13"
1. Zenetti Five 20x8.5 +40
2. Sevas S-55 20x8.5 +40 (just clears)
3. 5-Zigen FN01R-C 17x8 +43
Brembo
1.
StopTech
1. 14.1" 4 pod Amistad 19" Rotino 19X8.5 +37
2. 13" 4 pot, FN01R-C 17x9 +35 (track), otherwise OEM rims
3. 13" ST-40, FN01R-C 17x8 +35 (3-4mm of clearance)
4. 13" ST-40, Stock Mitsu EVO 8 Enkei 17x8 +38 (plenty of clearance)
5. 18x8*OEM; 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60 [F] & 4-Pot ST-45[R], (2-3mm clearance on rear is close, but works - 3-4mm front is Ok)
6. 18x9 SSR GT2-H (track) 335x32 Slotted AeroRotors [F&R] [6-Pot ST-60[F] & 4-Pot ST45[R] calipers (plenty of clearance F&R)
7. 19x8.5 Tenzo-R DC-5 Black 332x32 slotted 2 piece ST-40
8. 4-pot ST-40 355mmx32mm, Anceltion SPSIX Revo 20"x9.5" +27 high disk
9. 4-pot ST-40 355mmx32mm, Enkei NT03+M 18"x9.5" +27
10. 4-pot ST-40 355mmx32mm, RacingHart RS521 19x9.0 +26 (Good Clearance)
Endless
1. Endless 6 pod 14.1" Amistad 19" Rotino 19X8.5 +37
Project Mu
1.
Rotora
1. 6-pot 355mmx32mm Volk GT-7 19"x8.5" +23 high disk
2. 6-pot 355mmx32mm Junction Produce Scara Japan 19"x9.5" +23 high disk (needed 3mm spacer)
3. 6-pot 355mmx32mm Volk SF-Challenge 19x9.5 +28
4. 12-pot 380mmx34mm iForged Aero 20x8.5 +40 (sedan)
5.12 pot 380 mm HRE 944 20x9.5
6. 6-pot 355mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2.14.25" / 6 piston with 19" Seva S-Stars w/ 10MM Spacers (daily) & 18" MB Weapons (track)
Wilwood
1. 14.1" 6 piston Wilwood Stock 17" Sedan wheels
2. 13" x 1.37 rotors, SL-6 Wilwood, 17X8 5Zigen wheels
3. AZ Z Car kit, 13" 4-pot FSL, 5Zigen FNO1R-C 17x8 +43
4. 14" x 1.25" Wilwood factory drilled & slotted rotors/ Wilwood SL6 Calipers (Red) with Rays Eng. Coupe 19s
5. 14" Wilwood factory drilled and sloted rotors with 6 piston SL6 calipers same as candlestickpark but in black. 18 inch Ray's Engineering 350Z track (18x8 +30 offset)
Ksport
1.
AP Racing (Stillen)
1.14.25" / 6 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
2. Beware: '03 Coupe 18x8*OEM wheels; P/N AP3700 (front) 6-Pot w/14.25" rotors too tight to trust w/< 1mm -2mm! P/N AP3750 w/ 4-Pot is ok on rear. Stillen says should be OK on front, measure and decide 4 u-sef!
D2 Racing
1. 356mm / 8 piston with 19x8.5 Volk Racing GT-S (Sedan)
REAR:
Racing Brake
OEM with 13" rotor
1. Zenetti Five 20x10 +43
2. Sevas S-55 20x10 +40
Brembo
1.
StopTech
1. 13" 2-pot, FN01R-C 17x9 +35 (track), OEM otherwise
2. 4-pot ST-45 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip (does not fit without 10mm spacer!!!)
3. 13" 2-pot, iForged Essen 19x9.5 +45 and sometimes OEM sport 18's
4. 4-pot ST-45 355mmx32mm Anceltion SPSIX Revo 20"x10.5" +27 high disk
5. 4-pot ST-45 355mmx32mm Enkei NT03+M 18"x10.5" +30
6. 4-pot ST-45 355mmx32mm, RacingHart RS521 19x10.5 +22 (Barely Clears)
Endless
1.
Project Mu
1.
Rotora
1. 4-pot 355mmx32mm Volk GT-7 19"x9.5" +24 standard disk
2. 4-pot 355mmx32mm Junction Produce Scara Japan 19"x10.5" +24 medium disk with step lip
3. 4-pot 380mm x 34mm Maya GR5 20x10.5 +29
4. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (also Volk GT-C 20x9.5 +47)
5. 4-pot 355mm x 32mm Volk SF-Challenge 19x10.5 +23
6. 4-pot 355mm x 32mm iForged Aero 20x10 +42 (sedan)
7. 4 pot 380 mm HRE 944 20x11 (might change to 20x10.5) G37
8. 4-pot 332mm x 32mm Rota Torque 18x9.5(Rota P45R 18x9.5)
Megan
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc.
1. 13.5" 4 piston with 19" Seva S-Stars (daily) & 18" MB Weapons (track)
Wilwood
1. 13" 4 piston Wilwood factory kit with 18" Ray's Engineering 350Z Track 18's (18x8.5 +33 offset)
Ksport
1.
AP Racing (Stillen)
1. 13.5" 4 piston with 18" Nismo's 18" Axis Reverbs, most Volk wheels, etc
D2 Racing
1. 328mm / 6 piston with 19x9.5 Volk Racing GT-S (Sedan)