What did you do to the G today?
#8911
I drove ttrank's car solo
iTrader: (50)
Join Date: Mar 2009
Location: By the sea, Tx
Posts: 18,299
Received 1,487 Likes
on
1,222 Posts
G35 sedan w/ too much money in mods
#8912
Changed my alternator (old one tested bad) after going through my grounds didn't work and putting the original fluid back in the car as it still looks fresh. Followed FSM to the letter, but still no hot air coming out of the heater. I've tried using the bleeder to release pressure while the engine is still hot, letting air out until coolant comes out. I've repeated this process about 8 cooldown cycles now, and there's still no heat. I've squeezed the hoses to get bubbles out, I can still hear air but no bubbles come up, after each of the 8 cycles. Temp gauge is stable during extended revving.
Do I just need to keep doing this over and over? I've been at it for a solid 3 or 4 hours over the course of the day...
Do I just need to keep doing this over and over? I've been at it for a solid 3 or 4 hours over the course of the day...
#8914
#8915
Premier Member
iTrader: (11)
Well, every car EXCEPT my G got some love today.
Took delivery of a 2018 Armada on Thursday, and promptly dumped ECU data. By Friday afternoon, Uprev officially supported it (just need to find someone to tune it because I dunno what I'm doing, lol).
Today got the front windows tinted, and also went ahead and tinted the windows on the Kouki. Should have done that a few years ago!
Took delivery of a 2018 Armada on Thursday, and promptly dumped ECU data. By Friday afternoon, Uprev officially supported it (just need to find someone to tune it because I dunno what I'm doing, lol).
Today got the front windows tinted, and also went ahead and tinted the windows on the Kouki. Should have done that a few years ago!
#8916
Super Moderator
iTrader: (3)
Originally Posted by LoSt180
Well, every car EXCEPT my G got some love today.
Took delivery of a 2018 Armada on Thursday, and promptly dumped ECU data. By Friday afternoon, Uprev officially supported it (just need to find someone to tune it because I dunno what I'm doing, lol).
Today got the front windows tinted, and also went ahead and tinted the windows on the Kouki. Should have done that a few years ago!
Took delivery of a 2018 Armada on Thursday, and promptly dumped ECU data. By Friday afternoon, Uprev officially supported it (just need to find someone to tune it because I dunno what I'm doing, lol).
Today got the front windows tinted, and also went ahead and tinted the windows on the Kouki. Should have done that a few years ago!
Originally Posted by eazdaskeez
Finally mounted the new wheel setup. Rear tire is to beefy with the spacer because the fender lip is eating my tire. So it's either raise it or let the fender eat until it's full lol
#8919
#8920
#8921
#8922
#8923
Anybody here replaced their door lock actuators with that generic amazon kit (and following the DIY by python on this forum)? You guys happy with it?
Was going to purchase this since its only $4 more than the 2 pack...
In that same thread some guy posted the following: https://usactuators.com/shop?olsPage=products%2F2g35
Looks like someone just put the "kit" together by adding the wires...
Its either that or OEM remanufactured on ebay (with a lifetime warranty, just have to send back a core) for $120 shipped https://www.ebay.com/itm/Infiniti-G3...53.m1438.l2649
it looks like a HUGE pain in the dick to actually replace them though...
Was going to purchase this since its only $4 more than the 2 pack...
In that same thread some guy posted the following: https://usactuators.com/shop?olsPage=products%2F2g35
Looks like someone just put the "kit" together by adding the wires...
Its either that or OEM remanufactured on ebay (with a lifetime warranty, just have to send back a core) for $120 shipped https://www.ebay.com/itm/Infiniti-G3...53.m1438.l2649
it looks like a HUGE pain in the dick to actually replace them though...