continued revs after clutch pushed in.. yikes!
#1
continued revs after clutch pushed in.. yikes!
I really need some insight on this as i have searched and troubleshooted this issue that ive been having for some time now. So when driving and shifting gears normally you cant really tell except for a slight hanging of the RPM needle, no big deal however i notice the delay. now, whenever i give it some more throttle and shift, even at 4500-5000 RPM, and push the clutch in to change a gear, the RPMS and engine continually go up. about 500-800 RPMs very noticable. This side affect is linear because the more throttle i give the more aggrevated the rpms become. Its as if there is a severe delay in releaseing the gas pedal however no delay when pressing it. so obviously i cant drive hard because if i take it anywhere near red line the car will deffinately over rev.
Heres what i have already done,
-cleaned the throttle body
-bought new throttle body
-yes i release the gas pedal before clutching
-I also notice the RPMs, even at normal driving, are jumpy which has been a problem for a while now. I aleady replaced my dash cluster but the problem came back. I am wondering if it has a relation to this problem.
No idea what else to do. but its driving be cRAzY!
BTW i have built motor and turboed. HELP!!!!!!!!!!!!! i want to
Heres what i have already done,
-cleaned the throttle body
-bought new throttle body
-yes i release the gas pedal before clutching
-I also notice the RPMs, even at normal driving, are jumpy which has been a problem for a while now. I aleady replaced my dash cluster but the problem came back. I am wondering if it has a relation to this problem.
No idea what else to do. but its driving be cRAzY!
BTW i have built motor and turboed. HELP!!!!!!!!!!!!! i want to
![Driving](https://g35driver.com/forums/images/smilies/driving.gif)
#4
i didnt know there is a closed position relearn as well. I though there was only a idle air relearn. do you know how i do that? i already did. throttle position, idle air. ? I checked everything, from vacuum leaks to dirty MAF, to new throttle body, it just seems as if the release of the throttle pedal is really delayed causing the rpms to continually go up. pushing the throttle, it is instantaneous. but when i let go it takes a second to slow and drop. the more i press the gas the worse it is.
#5
Here:
https://g35driver.com/forums/g-spot/...ecu-reset.html
If that doesn't work or you already did it, I don't know. I'm just guessing simple stuff. If you're turbo, something may not be working as it should (wastegate, bov/bpv) and that could be causing something like what you're describing.
My only other suggestion is to reset the ecu and check your gas pedal to be sure it is able to move freely in both directions.
https://g35driver.com/forums/g-spot/...ecu-reset.html
If that doesn't work or you already did it, I don't know. I'm just guessing simple stuff. If you're turbo, something may not be working as it should (wastegate, bov/bpv) and that could be causing something like what you're describing.
My only other suggestion is to reset the ecu and check your gas pedal to be sure it is able to move freely in both directions.
#6
i actually just replaced my BOV to an HKS and it still does it. Good point though. Im wondering how a waste gate would cause this problem? never thought of that. I don't have the same problems as the link described. and i actually already did all of those ecu resetting procedures, I appreciate your help. anything else it could be or anyone else experience this?
#7
i actually just replaced my BOV to an HKS and it still does it. Good point though. Im wondering how a waste gate would cause this problem? never thought of that. I don't have the same problems as the link described. and i actually already did all of those ecu resetting procedures, I appreciate your help. anything else it could be or anyone else experience this?
When were you tuned recently?
Trending Topics
#8
I think i understand the issue. Ive been researching like crazy and the general consensus for this problem has to do with the Drive by wire system we have in the G. Apperently, the throttle butterfly will open fast but will close slowly for emissions purposes. here is something i found on a STI forum, they also have DBW.
And yes,...the stock slow close will help the turbo stay spooled a bit more. To combat the tendancy for the turbo to have to spool more after the shift you want a really good recirc valve. The only recirc one that opens fully that I have seen is the APS one. I dataloged the time to spool after a shift with the stock and APS valves. With the stock valve the turbo was back to full boost 305 miliseconds after I hit the gas again after the 1-2 shift. With the APS valve it was about 225 miliseconds. (as dataloged on my laptop using the ECUTEK Easy ECU cable) This represents a 30% faster spool-back after a shift. A well spent $249.
And yes,...the stock slow close will help the turbo stay spooled a bit more. To combat the tendancy for the turbo to have to spool more after the shift you want a really good recirc valve. The only recirc one that opens fully that I have seen is the APS one. I dataloged the time to spool after a shift with the stock and APS valves. With the stock valve the turbo was back to full boost 305 miliseconds after I hit the gas again after the 1-2 shift. With the APS valve it was about 225 miliseconds. (as dataloged on my laptop using the ECUTEK Easy ECU cable) This represents a 30% faster spool-back after a shift. A well spent $249.
#9
the question is how can i program the throttle to close faster? thats exactly what it feels like. as stated before. when i press the gas its instantaneous but when i release it takes a second for the throttle to close. maybe i should try a sprint booster. im surprised no one else has this issue.
#10
#12
#14