Could use some extra mechanical advice.
#1
Could use some extra mechanical advice.
Hey guys.
So it has finally happened. My clutch (what I presume my clutch) is shot.
I only say presume because I have been driving and started to feel the engagement point on my clutch pedal getting lower and lower and eventually I had to pump it to get into gear and then rev match shift to keep going. I checked my Slave Cylinder, It is new. I checked my Master Clutch Cylinder and it isn't leaking. Clutch Fluid is still full.
My clutch isn't slipping and still grabbing great.. I was wondering if this could be caused from any pressure plate fingers breaking or anything like that.
NOTES:
-I haven't taken anything apart yet.
-If it isn't the clutch I am still doing a full replacement of Clutch / Flywheel / Pressure Plate / Slave / Master / Clutch Lines / Rear Engine Seal (Cause why not) . It was on my to-do list anyways.
-I am no mechanic, just a son of a mechanic and have learned a little from being in the shop all the time.
-Transmission is being taken off this afternoon. And will post update tonight.
So it has finally happened. My clutch (what I presume my clutch) is shot.
I only say presume because I have been driving and started to feel the engagement point on my clutch pedal getting lower and lower and eventually I had to pump it to get into gear and then rev match shift to keep going. I checked my Slave Cylinder, It is new. I checked my Master Clutch Cylinder and it isn't leaking. Clutch Fluid is still full.
My clutch isn't slipping and still grabbing great.. I was wondering if this could be caused from any pressure plate fingers breaking or anything like that.
NOTES:
-I haven't taken anything apart yet.
-If it isn't the clutch I am still doing a full replacement of Clutch / Flywheel / Pressure Plate / Slave / Master / Clutch Lines / Rear Engine Seal (Cause why not) . It was on my to-do list anyways.
-I am no mechanic, just a son of a mechanic and have learned a little from being in the shop all the time.
-Transmission is being taken off this afternoon. And will post update tonight.
#2
Registered User
iTrader: (10)
Inside the clutch cylinder there's like a rubber plunger, when they go bad the plunger lets fluid by, your clutch pedal gets weaker and will eventually end up on the floor. You may be able to pull the pedal back up a few times but eventually you're dead in the water. This sounds like what's going on with your clutch. I replaced two of them on my last Z.
Gary
Gary
#3
An update:
Okay so I got the transmission pulled off yesterday and noticed that my throw out bearing was about to come through my pressure plate. I also noticed that my Flywheel/Clutch/Pressure Plate have been roasted inside; there were hot-spots everywhere.
I am about to replace the rear main seal here in a few days. Does anyone know if I have to drop the oil pan? Seems like the only logical choice at this point. I am already so far into it.
Side Note: I am actually pretty surprised on how easy the transmission was to remove.
I am about to replace the rear main seal here in a few days. Does anyone know if I have to drop the oil pan? Seems like the only logical choice at this point. I am already so far into it.
Side Note: I am actually pretty surprised on how easy the transmission was to remove.
The following users liked this post:
NemesisGee (05-12-2017)
#4
Registered User
iTrader: (10)
Hey guys.
So it has finally happened. My clutch (what I presume my clutch) is shot.
I only say presume because I have been driving and started to feel the engagement point on my clutch pedal getting lower and lower and eventually I had to pump it to get into gear and then rev match shift to keep going. I checked my Slave Cylinder, It is new. I checked my Master Clutch Cylinder and it isn't leaking. Clutch Fluid is still full. They don't leak if issues are internal!
My clutch isn't slipping and still grabbing great. Surprised with all the damage shown in the pic!
NOTES:
-I haven't taken anything apart yet.
-If it isn't the clutch I am still doing a full replacement of Clutch / Flywheel / Pressure Plate / Slave / Master / Clutch Lines / Rear Engine Seal (Cause why not) . It was on my to-do list anyways. This looks like your best idea, throwout bearing is a must replace!
-I am no mechanic, just a son of a mechanic and have learned a little from being in the shop all the time.
-Transmission is being taken off this afternoon. And will post update tonight.
So it has finally happened. My clutch (what I presume my clutch) is shot.
I only say presume because I have been driving and started to feel the engagement point on my clutch pedal getting lower and lower and eventually I had to pump it to get into gear and then rev match shift to keep going. I checked my Slave Cylinder, It is new. I checked my Master Clutch Cylinder and it isn't leaking. Clutch Fluid is still full. They don't leak if issues are internal!
My clutch isn't slipping and still grabbing great. Surprised with all the damage shown in the pic!
NOTES:
-I haven't taken anything apart yet.
-If it isn't the clutch I am still doing a full replacement of Clutch / Flywheel / Pressure Plate / Slave / Master / Clutch Lines / Rear Engine Seal (Cause why not) . It was on my to-do list anyways. This looks like your best idea, throwout bearing is a must replace!
-I am no mechanic, just a son of a mechanic and have learned a little from being in the shop all the time.
-Transmission is being taken off this afternoon. And will post update tonight.
The following users liked this post:
03G35C6MT (05-09-2017)
#5
#6
I am not to sure. I seen the hundreds of hot spots and just sat it to the side and haven't looked at it. I will check when I get to my shop. But if it is OEM then I have 94,000 on the car. But it definitely looks aftermarket to me. And on top of that the top transmission bolts that connect the transmission to the motor weren't torqued down AT ALL. So that leaves me to believe they have been in there before and got lazy towards the end.
#7
Trending Topics
#10
Update: I have completed the rear main seal and both moon seals (front and back). We couldn't find a solid place to put bolts into the engine to hoist it up so we wrapped chains around the motor mounts. That was a bad idea, it ripped them off and had to get new ones (they aren't cheap). I put them on last night along with putting the k-frame back into place.
The only problem we are still struggling with is my steering wheel's 'slip yoke' type thing doesn't move anymore. So It has become a PITA. ]
Hopefully will be done today.
The only problem we are still struggling with is my steering wheel's 'slip yoke' type thing doesn't move anymore. So It has become a PITA. ]
Hopefully will be done today.