G35 Sedan V35 2003-06 Discussion about the 1st Generation V35 G35 Sedan

TIEN inner & outer tie rods

Old Jun 1, 2007 | 11:06 PM
  #1  
killerlexus's Avatar
Thread Starter
|
Banned
iTrader: (1)
Joined: Jun 2005
Posts: 708
Likes: 0
From: san frisco
TIEN inner & outer tie rods

heres some before and after pics of TEIN INNER & OUTER tie rods.
parallel parking is alot easier and u tirns are a breeze. you can feel the steering wheel turn more before hitting steering stop.

1st pic before 2nd pic with tie rods
 
Attached Thumbnails TIEN inner & outer tie rods-before-t-r.jpg   TIEN inner & outer tie rods-wheelwitht-r.jpg  
Reply
Old Jun 1, 2007 | 11:08 PM
  #2  
killerlexus's Avatar
Thread Starter
|
Banned
iTrader: (1)
Joined: Jun 2005
Posts: 708
Likes: 0
From: san frisco
heres some for all you picture ******
 
Attached Thumbnails TIEN inner & outer tie rods-tierod-piece.jpg   TIEN inner & outer tie rods-tierodds.jpg   TIEN inner & outer tie rods-wheel-after.jpg  
Reply
Old Jun 2, 2007 | 12:36 AM
  #3  
5150DS's Avatar
Registered User
iTrader: (1)
Joined: Aug 2005
Posts: 3,984
Likes: 162
From: So Cal
Other than decreasing the turning radius, what do they do? Do they make the camber adjustable?
 
Reply
Old Jun 2, 2007 | 12:40 AM
  #4  
killerlexus's Avatar
Thread Starter
|
Banned
iTrader: (1)
Joined: Jun 2005
Posts: 708
Likes: 0
From: san frisco
no camber adjustments. my factory right outer was bad so i swapped for TEIN set instead of going OEM. this mod is more for 350z that do drifting,because it increases turn in angle.
 
Reply
Old Jun 2, 2007 | 12:49 AM
  #5  
5150DS's Avatar
Registered User
iTrader: (1)
Joined: Aug 2005
Posts: 3,984
Likes: 162
From: So Cal
How are you liking the 350z h-techs. I have thought about going this route for a slightly lower drop than the stock z springs.
 
Reply
Old Jun 2, 2007 | 01:17 AM
  #6  
ttrank's Avatar
Grocery getter
iTrader: (57)
Joined: Jul 2005
Posts: 27,305
Likes: 190
From: Phoenix
Premier Member

How much were they?
 
Reply
Old Jun 2, 2007 | 01:22 AM
  #7  
izmir41500's Avatar
G35driver Addict
iTrader: (4)
Joined: Feb 2005
Posts: 4,374
Likes: 1
From: SoCal
sweet. so the wheels don't lean into the turn, but turn more?
 
Reply

Trending Topics

Old Jun 2, 2007 | 04:01 AM
  #8  
perry05G35's Avatar
Registered User
iTrader: (4)
Joined: Aug 2005
Posts: 2,092
Likes: 0
From: San Antonio, TX
That's something I would like to have because mines sound terrible at times even after spraying with silicone where did you buy them and for how $$$?
 
Reply
Old Jun 2, 2007 | 10:45 AM
  #9  
TIRE_SMOKE96's Avatar
Registered User
Joined: Dec 2006
Posts: 1,529
Likes: 3
From: Hawaii
glad to see that my advice worked you!
 
Reply
Old Jun 2, 2007 | 10:50 AM
  #10  
chobble19's Avatar
Registered User
iTrader: (56)
Joined: Apr 2006
Posts: 3,394
Likes: 4
From: MIAMI
interesting..the turning radias sucks on our G's!
 
Reply
Old Jun 2, 2007 | 11:08 AM
  #11  
killerlexus's Avatar
Thread Starter
|
Banned
iTrader: (1)
Joined: Jun 2005
Posts: 708
Likes: 0
From: san frisco
http://www.wesellcarparts.com/store/...idproduct=4653

heres a sticky about the tie rods http://www.my350z.com/forum/showthre...light=tie+rods
 
Reply
Old Jun 2, 2007 | 02:19 PM
  #12  
GeeDM's Avatar
Registered User
iTrader: (1)
Joined: Dec 2006
Posts: 376
Likes: 1
From: Southern california
Damn i might have to look into these...hows the installation..pretty easy with a floor jack and jack stands or is a lift the way to go????
 
Reply
Old Jun 2, 2007 | 10:27 PM
  #13  
ttrank's Avatar
Grocery getter
iTrader: (57)
Joined: Jul 2005
Posts: 27,305
Likes: 190
From: Phoenix
Premier Member


That's not too bad. Thanks for the link.
 
Reply
Old Jun 2, 2007 | 10:43 PM
  #14  
VQPWR's Avatar
Registered User
iTrader: (2)
Joined: May 2006
Posts: 330
Likes: 0
From: Tampa,FL
Very nice...I might look into this
 
Reply
Old Jun 2, 2007 | 11:20 PM
  #15  
killerlexus's Avatar
Thread Starter
|
Banned
iTrader: (1)
Joined: Jun 2005
Posts: 708
Likes: 0
From: san frisco
if you search it can be had for 180 shipped.

my buddy installed the rods for me, so i couldnt tell you how hard it was, since i wasnt there to watch, but i will scan the instructions for ya'll to see tomarrow evening, i dont have instructions with me tonight.
 
Reply

Thread Tools
Search this Thread
Rate This Thread
Rate This Thread:
You have already rated this thread Rating: Thread Rating: 0 votes,  average.


All times are GMT -4. The time now is 11:48 AM.