CuztomPartZ Aluminum Engine Undershroud Fits the Sedan! :)
Jump up in the middle of the night a few times and tell her you've been having nightmares of a rock puncturing the oil pan?
Or tell her you just found out on Driver that not having a pan will void your warranty?
Or my fav, tell her it could do this...
Or tell her you just found out on Driver that not having a pan will void your warranty?
Or my fav, tell her it could do this...
Last edited by HwyDrftr; Dec 17, 2009 at 12:44 AM.
got a 3.5 FD pumpkin w/ VLSD & a new putter instead...but, I still want one of these
I'm worried about fitment...I know it will fit, I'm worried that the mounting holes on the bumper won't work because the stock undershroud got ripped off. I think the holes will be ripped out.
I'm worried about fitment...I know it will fit, I'm worried that the mounting holes on the bumper won't work because the stock undershroud got ripped off. I think the holes will be ripped out.
Just get the hardware kit with it and it should be fine. The holes are usually just ripped slightly on the bumper and the new hardware will clip over the remaining parts and hold it tight. If it doesnt work feel free to return for a full refund -shipping.
Got mine today. It wasn't packaged very well and took some damage. One of the ends of the lip portion is bent. Oh, well. It happens. I'm not sure how TT got his to mate up with his KurookieZ bumper, but mine is about 1 1/2"~2" off. I'm pretty certain he bent it, but it was raining and I was tired of being wet and getting cut by aluminum. Putting it at an angle I can see that it will reach no problem (as observed by TT's as well 
)
)
Got mine today. It wasn't packaged very well and took some damage. One of the ends of the lip portion is bent. Oh, well. It happens. I'm not sure how TT got his to mate up with his KurookieZ bumper, but mine is about 1 1/2"~2" off. I'm pretty certain he bent it, but it was raining and I was tired of being wet and getting cut by aluminum. Putting it at an angle I can see that it will reach no problem (as observed by TT's as well )
)Was there a sharp edge on the shield somewhere?
I take a lot of time to clean them up so there should be no sharp edges, Please let me know so I can fix it.
The aluminum version will no longer be available as soon as I run out of stock on them and I will be lowering the price on the PC version as it will be the only version avail. It is very hard the clean up the aluminum after they are cut and the PC process further helps on any edges that may be left.
Not sure what you mean on it being off by 2" or so. Is it not lining up horizontally or vertically? TT didnt mention anything about it being off with his K fascia?
The Kuruma is a lower bumper so it makes sense. I kind of expected it, but thought I would just bend it down. The Aluminum is more rigid than I expected.
About the sharp edge, it isn't razor sharp... Actually now that I think about it. It wasn't even the cover that was sharp. Sorry about that. It was the clips for the bolts. The ones that shipped with the spacers attached. Those were a pain to get off.
I really wanted to get the PC version, but couldn't justify the cost difference. Now that you say you are going to discount it. I wish I would've waited, lol. Really I just want the front section to be black so that it doesn't show through my gaping whole that is waiting for a intercooler
I'm going outside to take a picture of it so you can see the gap.
About the sharp edge, it isn't razor sharp... Actually now that I think about it. It wasn't even the cover that was sharp. Sorry about that. It was the clips for the bolts. The ones that shipped with the spacers attached. Those were a pain to get off.
I really wanted to get the PC version, but couldn't justify the cost difference. Now that you say you are going to discount it. I wish I would've waited, lol. Really I just want the front section to be black so that it doesn't show through my gaping whole that is waiting for a intercooler
I'm going outside to take a picture of it so you can see the gap.