G35 Sedan V35 2003-06 Discussion about the 1st Generation V35 G35 Sedan

Advice For New Wheels/Suspension

Thread Tools
 
Search this Thread
 
Rate Thread
 
  #46  
Old 06-26-2011 | 12:46 AM
4D05G35's Avatar
Registered User
iTrader: (6)
Joined: Dec 2009
Posts: 1,651
Likes: 50
From: WA
  #47  
Old 07-13-2011 | 10:56 PM
thn116's Avatar
Thread Starter
|
Registered User
Joined: Nov 2007
Posts: 246
Likes: 2
Hmmm that's pretty interesting. I was thinking about some BC coilovers.

Not to keep copying you MikeGD but what was your setup? Did you get the rear camber plates?
 
  #48  
Old 07-13-2011 | 11:05 PM
davidxu's Avatar
Registered User
iTrader: (3)
Joined: Sep 2009
Posts: 1,511
Likes: 15
From: Waterloo, ON
with htechs, you should'nt need a camber kit.

did you roll your fenders?

most people say coils because even if you go on springs sooner or later most people switch to coils and always regret going springs first.
 
  #49  
Old 07-13-2011 | 11:12 PM
thn116's Avatar
Thread Starter
|
Registered User
Joined: Nov 2007
Posts: 246
Likes: 2
Yea I know but I maybe looking into BC Racing coilovers now since the h tech's height won't look right with the wheels in my opinion.

I did not roll them. I probably will need to.
 
  #50  
Old 07-13-2011 | 11:15 PM
davidxu's Avatar
Registered User
iTrader: (3)
Joined: Sep 2009
Posts: 1,511
Likes: 15
From: Waterloo, ON
if you dont want to spend that much on coils, s techs are not bad.

you'll want your fenders rolled.

Also, how are you installing the springs/coils, by yourself or shop?

reason i ask is that... 4DGS and I tried to switch out my springs this past weekend.... spent a good couple hours on trying to get the front off but failed in the end, had to get a shop to do it.
 
  #51  
Old 07-13-2011 | 11:19 PM
thn116's Avatar
Thread Starter
|
Registered User
Joined: Nov 2007
Posts: 246
Likes: 2
Yea was thinking about that too but I like the ability to have adjustability when I want it.

Yea I figured as much when I posted pictures.

I was doing to do it with a few guys, but I could always have a shop do it. What went wrong? Bolt seized up?
 
  #52  
Old 07-13-2011 | 11:21 PM
davidxu's Avatar
Registered User
iTrader: (3)
Joined: Sep 2009
Posts: 1,511
Likes: 15
From: Waterloo, ON
we just didnt have a good impact gun to get the top bolt on the front struct off..
 
  #53  
Old 07-13-2011 | 11:27 PM
thn116's Avatar
Thread Starter
|
Registered User
Joined: Nov 2007
Posts: 246
Likes: 2
What springs did you get?
 
  #54  
Old 07-13-2011 | 11:28 PM
davidxu's Avatar
Registered User
iTrader: (3)
Joined: Sep 2009
Posts: 1,511
Likes: 15
From: Waterloo, ON
h-techs.

I'm still on stock wheels though.
 
  #55  
Old 07-13-2011 | 11:31 PM
thn116's Avatar
Thread Starter
|
Registered User
Joined: Nov 2007
Posts: 246
Likes: 2
Yea with this new wheel setup I'll definitely need coilovers and camber. Now its just the question of where to get them.
 
  #56  
Old 07-13-2011 | 11:32 PM
davidxu's Avatar
Registered User
iTrader: (3)
Joined: Sep 2009
Posts: 1,511
Likes: 15
From: Waterloo, ON
look through the vendor marketplace on the forum. The vendors here are good, anything happens mods step in fairly quickly.

GL.
 
  #57  
Old 07-13-2011 | 11:38 PM
thn116's Avatar
Thread Starter
|
Registered User
Joined: Nov 2007
Posts: 246
Likes: 2
Yea I been on there. Its going slow. I'm going to check in with the venders and see what's going on there.
 
  #58  
Old 07-14-2011 | 12:51 PM
MikeDG's Avatar
Registered User
iTrader: (6)
Joined: Nov 2010
Posts: 377
Likes: 20
From: Indy
Originally Posted by thn116
Hmmm that's pretty interesting. I was thinking about some BC coilovers.

Not to keep copying you MikeGD but what was your setup? Did you get the rear camber plates?
I have Megan racing rear camber arms and SPC toe bolts, but I still haven't gotten around to installing them yet.
 
  #59  
Old 07-15-2011 | 10:07 AM
thn116's Avatar
Thread Starter
|
Registered User
Joined: Nov 2007
Posts: 246
Likes: 2
Did you get a camber kit for the front? If you don't mind me asking where did you get your coilovers from?
 
  #60  
Old 07-15-2011 | 11:09 AM
pghg35sedan's Avatar
Registered User
iTrader: (6)
Joined: Apr 2010
Posts: 187
Likes: 9
From: Pittsburgh PA
I like my BC coilovers
 


You have already rated this thread Rating: Thread Rating: 0 votes,  average.

Quick Reply: Advice For New Wheels/Suspension



All times are GMT -4. The time now is 11:06 AM.