2005 G35 Turn signal Lights
#17
10-27-2005 | 12:08 AM
Registered User
Joined: Jun 2005
Posts: 333
Likes: 0
From: Scottsdale AZ
there's a sidemarker turn signal mod...
http://www.6mt.net/mod-g35-sidemarker.php
I plan on doing it once i get clear corners...
http://www.6mt.net/mod-g35-sidemarker.php
I plan on doing it once i get clear corners...
#21
10-28-2005 | 11:28 AM
#22
10-28-2005 | 11:34 AM
COURTESY OF RST531
************************************************** *******
Headlight Housing Blinker mod: Allows for amber bulb to remain off until used.
************************************************** *******
No need to cut any wires. All you need to do is modify the bulb's conductors. Remove the bulbs then cut the center wires (2 & 3) close to the glass. I also used electrical tape to cover the connections (2 & 3) just incase so that there is no contact. I will post a close up picture that will explain this later after I get home from work since I don't have it on my work comp.
The bulbs are a bitch to take out. If you have thin arms you can reach the passenger bulb from under the hood, but the drivers side you'll have to go through the fender well because the airbox is in the way.
They will only blink when signaling, and off rest of the time.
************************************************** *******
Headlight Housing Blinker mod: Allows for amber bulb to remain off until used.
************************************************** *******
No need to cut any wires. All you need to do is modify the bulb's conductors. Remove the bulbs then cut the center wires (2 & 3) close to the glass. I also used electrical tape to cover the connections (2 & 3) just incase so that there is no contact. I will post a close up picture that will explain this later after I get home from work since I don't have it on my work comp.
The bulbs are a bitch to take out. If you have thin arms you can reach the passenger bulb from under the hood, but the drivers side you'll have to go through the fender well because the airbox is in the way.
They will only blink when signaling, and off rest of the time.
Last edited by Gee Im Fast; 10-29-2005 at 04:33 PM.
#23
10-28-2005 | 11:41 AM
Joined: Jan 2004
Posts: 21,095
Likes: 47
From: Toronto, GTA north
Originally Posted by Gee Im Fast
COURTESY OF RST531
No need to cut any wires. All you need to do is modify the bulb's conductors. Remove the bulbs then cut the center wires (2 & 3) close to the glass. I also used electrical tape to cover the connections (2 & 3) just incase so that there is no contact. I will post a close up picture that will explain this later after I get home from work since I don't have it on my work comp.
The bulbs are a bitch to take out. If you have thin arms you can reach the passenger bulb from under the hood, but the drivers side you'll have to go through the fender well because the airbox is in the way.
They will only blink when signaling, and off rest of the time.
No need to cut any wires. All you need to do is modify the bulb's conductors. Remove the bulbs then cut the center wires (2 & 3) close to the glass. I also used electrical tape to cover the connections (2 & 3) just incase so that there is no contact. I will post a close up picture that will explain this later after I get home from work since I don't have it on my work comp.
The bulbs are a bitch to take out. If you have thin arms you can reach the passenger bulb from under the hood, but the drivers side you'll have to go through the fender well because the airbox is in the way.
They will only blink when signaling, and off rest of the time.
I like the solution; simple & no cutting into the harness
Thread
Thread Starter
Forum
Replies
Last Post
2005, aim, clear, covers, g35, headlight, headlights, johnnlucgmailcom, light, night, replacement, signal, signals, turn, wedge
