20x8.5 +40 with 10mm spacer

Thread Tools
 
Search this Thread
 
Rate Thread
 
  #16  
Old 03-19-2008 | 02:04 PM
Jeff92se's Avatar
Red Card Crew
iTrader: (24)
Joined: May 2005
Posts: 37,810
Likes: 583
From: ɐʍ 'ǝlʇʇɐǝs
Premier Member
Eh, some of the pics looked like they stick out. What size tires you running Ernie?

3mm like I said, fine line

Then again, I don't have much of a choice + I want to run 235s in the rear.
 
  #17  
Old 03-19-2008 | 02:08 PM
MixturePinoy's Avatar
Banned
iTrader: (9)
Joined: Feb 2006
Posts: 11,076
Likes: 6
From: Washington State
Jeff... your rears stick out a bit as well.. arent you running the coupe staggered fitment oem 19's?
 
  #18  
Old 03-19-2008 | 02:10 PM
Jeff92se's Avatar
Red Card Crew
iTrader: (24)
Joined: May 2005
Posts: 37,810
Likes: 583
From: ɐʍ 'ǝlʇʇɐǝs
Premier Member
Mine are on the ragged edge yes. I plan on running 235s if I can. But I'm not lowered yet. Like I said, it looked like it stuck out in some of the pics. And again, I don't have much choice.

 
  #19  
Old 03-19-2008 | 02:24 PM
G35Papa's Avatar
Registered User
iTrader: (85)
Joined: Jun 2003
Posts: 14,505
Likes: 451
From: NorCal
Looks good Lumpia but get some better pics up when you can
 
  #20  
Old 03-19-2008 | 02:32 PM
FlyingLumpia's Avatar
Thread Starter
|
Registered User
iTrader: (7)
Joined: Jul 2006
Posts: 3,284
Likes: 38
From: Washington State
I am running 245/35/20, I could go with a 235 or 225 and stretch it. LOL. I once I get the fenders rolled and wash it. I will take better pics. Like I said, I was tired just got home put them on to test and took them off.
 
  #21  
Old 03-19-2008 | 02:38 PM
Jeff92se's Avatar
Red Card Crew
iTrader: (24)
Joined: May 2005
Posts: 37,810
Likes: 583
From: ɐʍ 'ǝlʇʇɐǝs
Premier Member
Looks like both of us could use the 235s.
Specification Sidewall Radius Diameter Circumference Revs/Mile Difference
215/55-17 4.7in 13.2in 26.3in 82.7in 767 0.0%
245/35-20 3.4in 13.4in 26.8in 84.0in 754 1.7%
245/40-19 3.9in 13.4in 26.7in 83.9in 755 1.5%
235/35-20 3.2in 13.2in 26.5in 83.2in 762 0.6%
235/40-19 3.7in 13.2in 26.4in 82.9in 764 0.3%
 
  #22  
Old 03-19-2008 | 02:44 PM
FlyingLumpia's Avatar
Thread Starter
|
Registered User
iTrader: (7)
Joined: Jul 2006
Posts: 3,284
Likes: 38
From: Washington State
But there is not much of a tire selection 235/35/20.
 
  #23  
Old 03-19-2008 | 02:56 PM
psedog's Avatar
Back in SD**
iTrader: (4)
Joined: Oct 2006
Posts: 3,908
Likes: 63
From: San Diego
Premier Member
Originally Posted by Jeff92se
Looks like both of us could use the 235s.
Specification Sidewall Radius Diameter Circumference Revs/Mile Difference
215/55-17 4.7in 13.2in 26.3in 82.7in 767 0.0%
245/35-20 3.4in 13.4in 26.8in 84.0in 754 1.7%
245/40-19 3.9in 13.4in 26.7in 83.9in 755 1.5%
235/35-20 3.2in 13.2in 26.5in 83.2in 762 0.6%
235/40-19 3.7in 13.2in 26.4in 82.9in 764 0.3%
Edit, I'm stupid. Didn't notice the inch section.
 
  #24  
Old 03-21-2008 | 11:32 AM
ttrank's Avatar
Grocery getter
iTrader: (57)
Joined: Jul 2005
Posts: 27,305
Likes: 190
From: Phoenix
Premier Member
Did you roll yet? I think you will be good to go when they are rolled.
 
  #25  
Old 03-21-2008 | 01:24 PM
Jeff92se's Avatar
Red Card Crew
iTrader: (24)
Joined: May 2005
Posts: 37,810
Likes: 583
From: ɐʍ 'ǝlʇʇɐǝs
Premier Member
Okay I took a look at my setup. It's almost like Ernie's lowrider version. Sorry Ernie. We can have a caged midget fight at the premeet up at northgate. Loser buys lattes. okay? lol
 
  #26  
Old 03-21-2008 | 02:22 PM
FlyingLumpia's Avatar
Thread Starter
|
Registered User
iTrader: (7)
Joined: Jul 2006
Posts: 3,284
Likes: 38
From: Washington State
If everything goes right, I should have them rolled tomorrow morning around 8am.
 
  #27  
Old 03-21-2008 | 02:24 PM
Jeff92se's Avatar
Red Card Crew
iTrader: (24)
Joined: May 2005
Posts: 37,810
Likes: 583
From: ɐʍ 'ǝlʇʇɐǝs
Premier Member
Who's doing it? Hai-san?
 
  #28  
Old 03-21-2008 | 02:42 PM
godmans's Avatar
Registered User
iTrader: (22)
Joined: May 2004
Posts: 2,239
Likes: 4
Get it rolled, you should be fine
 
  #29  
Old 03-22-2008 | 01:14 PM
FlyingLumpia's Avatar
Thread Starter
|
Registered User
iTrader: (7)
Joined: Jul 2006
Posts: 3,284
Likes: 38
From: Washington State
Got them rolled, didn't hear no rubbing. Working today until 1 and if it stays decent here, I will wash and take pictures for you guys.
 
  #30  
Old 03-22-2008 | 08:10 PM
FlyingLumpia's Avatar
Thread Starter
|
Registered User
iTrader: (7)
Joined: Jul 2006
Posts: 3,284
Likes: 38
From: Washington State
Well I hope these show the difference alittle better.

Before.


After.




Now I am just whoring.

 


You have already rated this thread Rating: Thread Rating: 0 votes,  average.

Quick Reply: 20x8.5 +40 with 10mm spacer



All times are GMT -4. The time now is 07:35 PM.