Vortech S/C Installed and tuned @ CIN

Thread Tools
 
Search this Thread
 
Rate Thread
 
Old Jan 24, 2011 | 11:31 AM
  #1  
GrocryGettr's Avatar
Thread Starter
|
Registered User
Joined: Nov 2008
Posts: 348
Likes: 8
From: Charlotte, NC
Vortech S/C Installed and tuned @ CIN

This was a 6MT, non-rev, stock engine with our CIN Xhaust installed and tuned last week.


395HP / 339TQ
 
Reply
Old Jan 24, 2011 | 10:27 PM
  #2  
bash27jp00's Avatar
Ohio G Club Member
iTrader: (2)
Joined: Jan 2009
Posts: 662
Likes: 1
From: cleveland, Ohio
nice!
 
Reply
Old Jan 24, 2011 | 11:19 PM
  #3  
doeboy's Avatar
Registered User
iTrader: (6)
Joined: May 2010
Posts: 516
Likes: 28
From: Moving to D.C.
Very sweet...Right at the 400 mark
 
Reply
Old Jan 25, 2011 | 06:05 AM
  #4  
Dsskyline's Avatar
Registered User
iTrader: (15)
Joined: Oct 2003
Posts: 2,729
Likes: 84
From: Owings Mills MD
Originally Posted by GrocryGettr
This was a 6MT, non-rev, stock engine with our CIN Xhaust installed and tuned last week.


395HP / 339TQ
Nice!! Which pulley was used and do you have pics of your CIN exhaust?
 
Reply
Old Jan 25, 2011 | 09:44 AM
  #5  
GrocryGettr's Avatar
Thread Starter
|
Registered User
Joined: Nov 2008
Posts: 348
Likes: 8
From: Charlotte, NC
Originally Posted by Dsskyline
Nice!! Which pulley was used and do you have pics of your CIN exhaust?
It was suppossed to be a 9 psi pulley, but the most we saw on the dyno was 8.2 psi. Even on the street afterwards, the guage only showed 8 psi.
We will wait until he has us build him an engine to go up on the boost. He is quite satisfied right now!

As to our exhaust, we have three prototypes on the street right now making sure that there are no issues with the kits before we release them.
This customer asked that we used Flowmaster Series 40 mufflers on his car. I told him that it wouldn't sound good but with our front and mid section used, we tucked the Flowmasters behind the axle and it doesn't sound bad.
 
Reply
Old Jan 25, 2011 | 01:45 PM
  #6  
CLyons0203's Avatar
Registered User
iTrader: (5)
Joined: Jul 2007
Posts: 471
Likes: 5
Nice power! I'm located in Raleigh NC. I might go to you guys for a tune.
 
Reply
Old Jan 25, 2011 | 02:17 PM
  #7  
GrocryGettr's Avatar
Thread Starter
|
Registered User
Joined: Nov 2008
Posts: 348
Likes: 8
From: Charlotte, NC
Originally Posted by CLyons0203
Nice power! I'm located in Raleigh NC. I might go to you guys for a tune.
Sounds good, we have some power waiting for ya.
 
Reply
Old Jan 25, 2011 | 06:15 PM
  #8  
Dsskyline's Avatar
Registered User
iTrader: (15)
Joined: Oct 2003
Posts: 2,729
Likes: 84
From: Owings Mills MD
Originally Posted by GrocryGettr
It was suppossed to be a 9 psi pulley, but the most we saw on the dyno was 8.2 psi. Even on the street afterwards, the guage only showed 8 psi.
We will wait until he has us build him an engine to go up on the boost. He is quite satisfied right now!

As to our exhaust, we have three prototypes on the street right now making sure that there are no issues with the kits before we release them.
This customer asked that we used Flowmaster Series 40 mufflers on his car. I told him that it wouldn't sound good but with our front and mid section used, we tucked the Flowmasters behind the axle and it doesn't sound bad.
is this the V-8 sounding one you talked to me about a few months ago when I was going to buy your modified for a G35 GTR exhaust.

Can't wait to see some before and after numbers along with sound.
 
Reply
Old Jan 25, 2011 | 08:36 PM
  #9  
GrocryGettr's Avatar
Thread Starter
|
Registered User
Joined: Nov 2008
Posts: 348
Likes: 8
From: Charlotte, NC
Originally Posted by Dsskyline
is this the V-8 sounding one you talked to me about a few months ago when I was going to buy your modified for a G35 GTR exhaust.

Can't wait to see some before and after numbers along with sound.
Well, sort of. The first system we created with the Flowmasters sounded great at low rpm, BUT!, at wot, it sounded like a pack of Honda's running full out through a tunnel. So, about the same time, we finished the last version of our afore mentioned exhaust. We deleted the front and mid section on the Flowmaster system and fitted the prototypes on to it. The result was that while the low end rumble wasn't as prevalent, at wot, there was no resonation at all.
It is quieter with the Flowmasters than with our mufflers, but doesn't make quite the hp.

I don't have any video of the flowmasters on the G35, but I will make one of the prototype exhaust along with the dyno sheets. Give me a couple of days since we are very busy right now.
 
Reply
Old Jan 25, 2011 | 09:22 PM
  #10  
the_sedan's Avatar
Registered User
iTrader: (26)
Joined: Sep 2009
Posts: 3,082
Likes: 20
From: ATL hoe
what was the full mod list for this car? bolt-ons?
 
Reply
Old Jan 26, 2011 | 07:35 AM
  #11  
GrocryGettr's Avatar
Thread Starter
|
Registered User
Joined: Nov 2008
Posts: 348
Likes: 8
From: Charlotte, NC
Originally Posted by the_coupe
what was the full mod list for this car? bolt-ons?
5/16 MD Iso, CIN Xhaust, DW 600cc injectors, Vortech S/C (oil fed), custom Osiris tune
 
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
StreetStandard
Engine-Vendor
117
May 22, 2020 08:21 AM
redonblack35
Accessories
19
Feb 13, 2016 11:19 AM
usingthejohn
Media Share G35 Sedan V35
7
Sep 17, 2015 11:37 AM



You have already rated this thread Rating: Thread Rating: 0 votes,  average.


All times are GMT -4. The time now is 08:53 PM.