G35Driver - Infiniti G35 & G37 Forum Discussion
Here's a shot from the front side of the tire
Here's a shot from the front side of the tire
0 2019/05/02 18:04:49
0 2019/05/08 02:42:02
See those two washers I put in between the exhaust piping flange? It lets some of the sound escape through there. Most of it still goes thru the muffler so it still sounds the same...this just adds some depth to it. I did a lot of expermineting with different gaps and this was the perfect balance. Do this to only one of the bolts on the flange. If done to both, it will be too big of a gap, too loud and will change the exhaust tone. I used 2 washers...1/16" thickness each. So total 1/8" gap.
See those two washers I put in between the exhaust piping flange? It lets some of the sound escape through there. Most of it still goes thru the muffler so it still sounds the same...this just adds some depth to it. I did a lot of expermineting with different gaps and this was the perfect balance. Do this to only one of the bolts on the flange. If done to both, it will be too big of a gap, too loud and will change the exhaust tone. I used 2 washers...1/16" thickness each. So total 1/8" gap.
0 2019/05/14 16:18:46
0 2019/05/17 10:25:30
Lookin all nice n śhit.
Lookin all nice n śhit.
0 2019/05/30 18:07:34
0 2019/06/04 16:20:01
0 2019/06/06 21:14:30
0 2019/06/08 18:13:06
0 2019/06/08 18:13:24
0 2019/06/08 18:15:29
0 2019/06/08 18:15:45
0 2019/06/08 18:16:12
0 2019/07/30 17:35:14
0 2019/08/18 18:00:38
0 2019/08/18 18:00:47
0 2019/08/18 18:00:59
0 2019/08/18 18:01:12
0 2019/09/11 17:15:03
0 2019/09/15 21:01:16
0 2019/09/28 12:14:14
0 2019/09/28 12:14:22
As for adjusting the headlights up/down, there is a hole on the headlight assembly itself where u can stick a phillips screwdriver in and turn the teeth to move the beam up or down.
As for adjusting the headlights up/down, there is a hole on the headlight assembly itself where u can stick a phillips screwdriver in and turn the teeth to move the beam up or down.
0 2019/11/01 17:54:38
Here is the hole and u can see the adjusting teeth in there. However, no matter how much I tried to adjust it using those teeth the screwdriver would just not turn freely. It takes quite a bit of turning to get the beam to move. So I got frustrated and used a dremel to cut off the plastic around it so I can adjust the beam using the screw on the back side.
Here is the hole and u can see the adjusting teeth in there. However, no matter how much I tried to adjust it using those teeth the screwdriver would just not turn freely. It takes quite a bit of turning to get the beam to move. So I got frustrated and used a dremel to cut off the plastic around it so I can adjust the beam using the screw on the back side.
0 2019/11/01 17:55:01
I adjusted it using this screw. I had use a small bit ratchet to get in there because there isnt much clearance behind it to fit a screwdriver.
I adjusted it using this screw. I had use a small bit ratchet to get in there because there isnt much clearance behind it to fit a screwdriver.
0 2019/11/01 17:55:28
0 2019/12/12 02:03:02
0 2019/12/15 15:26:07
With navi
With navi
0 2019/12/19 09:59:38
Without navi
Without navi
0 2019/12/19 10:00:01
0 2019/12/28 00:57:00
0 2019/12/28 11:27:06
0 2020/01/17 17:52:19
0 2020/01/17 17:54:02
0 2020/01/22 21:37:34
0 2020/02/02 15:27:29
0 2020/02/02 15:27:55
0 2020/02/02 15:28:22
0 2020/02/02 15:28:51
0 2020/02/02 15:29:15
0 2020/02/02 15:29:35
0 2020/02/02 15:29:56