FS: NITROUS SETUP, 90% Complete
Joined: Jun 2006
Posts: 1,359
Likes: 2
From: Atlanta, GA
FS: NITROUS SETUP, 90% Complete
I've decided that I'm not going to install the nitrous system in my car, so here it is. I'll have pics tomorrow. I would like to sell this as a complete kit, but if there is a lack of interest in the complete kit, then I'll consider parting it out.
Here is what is included:
-NX 10lb bottle with mounting brackets; the bottle is about 3/4 full, but I'll weigh it to get a more exact amount
-NX bottle heater w/ solenoid - I verified that the cutoff PSI of the solenoid is 1000 psi.
-bottle pressure gauge - I work in a calibration lab and adjusted this gauge to be dead-on accurate. The bezel ring was not a pop-off type, so it is a little bent where I had to take it off to adjust the needle, but it works perfectly and gives the correct reading.
-NOS remote bottle opener
-about 15' of primary nitrous line and about a meter each of fuel and nitrous lines from the solenoids to the nozzle. I pressure checked all of the lines.
-NX fuel/n2o solenoids
-NX Shark nozzle with new 52/26 jets (100 shot)
-NX Purge solenoid and new nylon purge line
-Dynotune electronic TPS/RPM 2 channel window switch. I purchased this new, and it is currently installed in my car, but it has never been used. Product info: http://www.dynotunenitrous.com/store...?idproduct=194
-brand new fuel pressure safety switch
-fuel line adapter (like the one from AAM)
-Custom made (by me) 4-switch control box
-various fittings/adapters, wiring, etc.
The only two things that should be added are a nitrous filter and 1 step colder plugs.
Pics should be up tomorrow evening.
I'm asking $600 + shipping.
Here is what is included:
-NX 10lb bottle with mounting brackets; the bottle is about 3/4 full, but I'll weigh it to get a more exact amount
-NX bottle heater w/ solenoid - I verified that the cutoff PSI of the solenoid is 1000 psi.
-bottle pressure gauge - I work in a calibration lab and adjusted this gauge to be dead-on accurate. The bezel ring was not a pop-off type, so it is a little bent where I had to take it off to adjust the needle, but it works perfectly and gives the correct reading.
-NOS remote bottle opener
-about 15' of primary nitrous line and about a meter each of fuel and nitrous lines from the solenoids to the nozzle. I pressure checked all of the lines.
-NX fuel/n2o solenoids
-NX Shark nozzle with new 52/26 jets (100 shot)
-NX Purge solenoid and new nylon purge line
-Dynotune electronic TPS/RPM 2 channel window switch. I purchased this new, and it is currently installed in my car, but it has never been used. Product info: http://www.dynotunenitrous.com/store...?idproduct=194
-brand new fuel pressure safety switch
-fuel line adapter (like the one from AAM)
-Custom made (by me) 4-switch control box
-various fittings/adapters, wiring, etc.
The only two things that should be added are a nitrous filter and 1 step colder plugs.
Pics should be up tomorrow evening.
I'm asking $600 + shipping.
Joined: Jun 2006
Posts: 1,359
Likes: 2
From: Atlanta, GA
Pics are ready:
http://my350z.com/forum/showthread.p...23#post3205923
Please respond in the above link, not here, if you would like to purchase this.
Thank you!!
http://my350z.com/forum/showthread.p...23#post3205923
Please respond in the above link, not here, if you would like to purchase this.
Thank you!!
wow.. that's cheap.. good luck on the sale
Trending Topics
Joined: Jun 2006
Posts: 1,359
Likes: 2
From: Atlanta, GA
bump.
Well, I'm unexpectedly back from my work trip. I got a call that there's been a family emergency, so I had to come back. I'm about to leave for my mother's house, so if you don't hear from me immediately, don't be alarmed. I'll try to check in as often as I can.
Thanks.
Well, I'm unexpectedly back from my work trip. I got a call that there's been a family emergency, so I had to come back. I'm about to leave for my mother's house, so if you don't hear from me immediately, don't be alarmed. I'll try to check in as often as I can.
Thanks.
