Compression rod / Lower control arm ... little confused HELP
Registered User
Joined: Dec 2007
Posts: 112
Likes: 3
From: Sin City
G Sedan
Good info , were all screwed for now. The Nismo and Whiteline bushing are both on backorder till sometime in may.
Yup both of mine are blown, i noticed when i was putting my car back into street trim.
Yup both of mine are blown, i noticed when i was putting my car back into street trim.
Registered User
iTrader: (3)
Joined: May 2007
Posts: 4,383
Likes: 27
From: pinellas county FLA, queens N.Y.
bump for a different supplier?
Registered User
Joined: Nov 2007
Posts: 145
Likes: 0
From: SoCal
Last edited by DDD*G35; Apr 21, 2009 at 02:39 AM. Reason: add
Registered User
Joined: Dec 2007
Posts: 112
Likes: 3
From: Sin City
G Sedan
subscribed for transverse link bushing source... mine is shot - my alignment guy has press... Performance Nissan (mynismo) is within driving distance - I guess I wait till May unless someone finds a source
Joined: Jul 2007
Posts: 237
Likes: 0
From: Las Vegas, NV
Havent been around since i sold my G35... i will tell you when i ordered mine they were out of stock also. Told me it would be a month wait, after i ordered it was actually only a 2 week wait and keep in mind if you wait till its "in stock" they will fill the orders that are already waiting before they get to you. So you might as well order the ish now and just get in line since you know that you need it.
I bought mine from http://www.jscspeed.com/350z/suspension/wlp_bushings.htm
I have access to hydraulic press but couldn’t find suitable size ID & OD piece of pipe to push out old bushings. What are you using to push bushing without damaging the arm?
I have access to hydraulic press but couldn’t find suitable size ID & OD piece of pipe to push out old bushings. What are you using to push bushing without damaging the arm?
Joined: Jul 2007
Posts: 237
Likes: 0
From: Las Vegas, NV
I bought mine from http://www.jscspeed.com/350z/suspension/wlp_bushings.htm
I have access to hydraulic press but couldn’t find suitable size ID & OD piece of pipe to push out old bushings. What are you using to push bushing without damaging the arm?
I have access to hydraulic press but couldn’t find suitable size ID & OD piece of pipe to push out old bushings. What are you using to push bushing without damaging the arm?
Use a socket... its the easiest and most common.
Registered User
Joined: Jul 2009
Posts: 87
Likes: 0
heres a link if u still lookin i found it after i spent 400 to replace that lower control arm the shop screwed me but jus a learnin exp i guess
http://www.g35nyc.com/forums/showthread.php?p=421577
http://www.g35nyc.com/forums/showthread.php?p=421577
^^^ good find 
Might be easier to link it this way though:
http://www.z1auto.com/prodmore.asp?m...ng&prodid=3783
Adam (Z-1) is a good guy – very knowledgeable… his shipping is real fast too!
Might be easier to link it this way though:
http://www.z1auto.com/prodmore.asp?m...ng&prodid=3783
Adam (Z-1) is a good guy – very knowledgeable… his shipping is real fast too!
Registered User
Joined: Nov 2008
Posts: 19
Likes: 0
Is this for a pair of bushings that would cover both the right and left side? I am just wondering if I need to order 2 to do both sides done.
^^^ good find
Might be easier to link it this way though:
http://www.z1auto.com/prodmore.asp?m...ng&prodid=3783
Adam (Z-1) is a good guy – very knowledgeable… his shipping is real fast too!
Might be easier to link it this way though:
http://www.z1auto.com/prodmore.asp?m...ng&prodid=3783
Adam (Z-1) is a good guy – very knowledgeable… his shipping is real fast too!