DIY for Clear Corners?
#1
#2
#4
Re: DIY for Clear Corners?
I was more concerned about which bolts to pull out in the wheel well. Didn't want to pull out too many, just the ones I needed. Am I suppose to take the whole fender off, or just pull it back?
Twilight Blue G35 Coupe 6MT
Premium - Nav - Aero - Trunk Mat
Injen CAI
Twilight Blue G35 Coupe 6MT
Premium - Nav - Aero - Trunk Mat
Injen CAI
#5
Re: DIY for Clear Corners?
From the manual
G35C - 6MT, DG/G, Aero, BSM, Flaps, Stillen Intake, Z tube, Crawford v5, 6 Wire Grounding Kit, Clear Corners, 2nd Battery (Brake) Cover, Sirius, Momo F16 Evo Shifter, 30% 3M Tint & more to go
193160-sidemarker.jpg
G35C - 6MT, DG/G, Aero, BSM, Flaps, Stillen Intake, Z tube, Crawford v5, 6 Wire Grounding Kit, Clear Corners, 2nd Battery (Brake) Cover, Sirius, Momo F16 Evo Shifter, 30% 3M Tint & more to go
193160-sidemarker.jpg
#6
Re: DIY for Clear Corners?
You don't need any tools. Just pull on it from the wheel well corner. Pops out real easily.
---------------------------------
http://www.anythingbox.net
---------------------------------
http://www.anythingbox.net
#7
Trending Topics
#8
Re: DIY for Clear Corners?
Dan,
which bulb are you trying to clear out? You refer to pulling bolts from the wheel well which suggests you are trying to clear corner the blinker in the headlight housing. If that is the case then it is a bit more complicated, if it is the sidemarker then as said above it is cake.
If you want the headlight housing out do the following.
1. Jack up the car, not all the way, just enough to get some working room between the top of the tire and the wheel well (removing the tire helps but is not necessary unless you are a contestant on world's strongest man).
2. Just start removing bolts and clips. There are DIY posts on which ones you need to remove and which you don't, but they aren't hard to remove and if you do it right no damage should be done so I just removed them all.
3. Pull away the plastic until you can get your hands through to the headlight housing.
Do the steps in reverse to reassemble.
ALso, it should be noted that making that bulb clear is not really a DIY project, you pretty much have to buy a new housing as otherwise it involves breaking the housing then eposying it back together.
SOrry for the long post, but hope it helps.
Some mistakes are too much fun to only make once.
2004 G35 coupe - 4150K high/fogs - more to come
which bulb are you trying to clear out? You refer to pulling bolts from the wheel well which suggests you are trying to clear corner the blinker in the headlight housing. If that is the case then it is a bit more complicated, if it is the sidemarker then as said above it is cake.
If you want the headlight housing out do the following.
1. Jack up the car, not all the way, just enough to get some working room between the top of the tire and the wheel well (removing the tire helps but is not necessary unless you are a contestant on world's strongest man).
2. Just start removing bolts and clips. There are DIY posts on which ones you need to remove and which you don't, but they aren't hard to remove and if you do it right no damage should be done so I just removed them all.
3. Pull away the plastic until you can get your hands through to the headlight housing.
Do the steps in reverse to reassemble.
ALso, it should be noted that making that bulb clear is not really a DIY project, you pretty much have to buy a new housing as otherwise it involves breaking the housing then eposying it back together.
SOrry for the long post, but hope it helps.
Some mistakes are too much fun to only make once.
2004 G35 coupe - 4150K high/fogs - more to come
#9
#10
#11