what is stock G35 coupe's 0 to 60? I couldnt figure it out.

 

I have a stock 5 speed auto and if I just punch it in "drive " mode on a good day i get around 5.7, have not tried it in the manuamatic mode but it depend on where you get the times from . magazines or real experiences.
K& N filter is my only modification

 

6MTs have tested out between 5.5 and 6, Autos in the low sixes

 

That is not correct unless you are talking about stock. My first ever run was a 5.7 0 to 60 in manual mode after my intake mod. I have an AT

04 Carib Blu
Pre Pkg w Areo Kit & Wing
Sat radio
7 Wire Grounding Kit ( Blue ) Z-Xtreme.com
Injen Intake
30% tint all around
Skyline Badges
Vector FX 2 accelometer
AC Mod
Personal Plate ( I Candy )

 

How did you guys record your times? With a g-tech or something? Just curious.

2004 6MT (Silver/Willow), premium & aero packages

My old ride (I still miss her; put a lot of pride and joy into it): http://www.n-body.net/registry/john95ga/

 

Vector FX 2 accelometer By Bell
Measures
0 to 60
G Force
Braking distance
60 70 80 90 on up to 1000 ft times
HP Min Max and Peak
Rear Wheel HP
Or Engine HP
1/4 Mile times and speed
Downloading info or times
A lot to much to list
This thing is AWSOME>..

Go to www.Beltronics.com

 

FORTE, Sounds too good to be true for one little device. Are you sure the Bell is accurate or is there a percentage of error ratio. It's hard for me to believe that a 3400 lb. car with only an intake mod boosting maybe 5-8 RWHP to the existing 225-235RWHP, is posting 5.7 0-60 times with an AT. It just kinda doesn't add up with physics. Have you taken it to the drag strip?

-Jason
Laser Red '03 6MT

 

I have the FX1 and I tried it at the track it showed about a second slower run than I actually had, so yea there is a margin of error, its a guide and a cool toy thats it.

Crawford Plenum / Z tube + Stillen Hi-Flow / Borla Dual Exhaust / Stillen Xdrilled+Stotted Rotors
Best 1/4 mile 14.469 @ 97.61, 60ft 2.399

 

ahhh and as far as AT vs MT I have seen an AT do 14.0 and 14.1 best in a quarter with comparable mods so there you go.

Crawford Plenum / Z tube + Stillen Hi-Flow / Borla Dual Exhaust / Stillen Xdrilled+Stotted Rotors
Best 1/4 mile 14.469 @ 97.61, 60ft 2.399

 

I'm quite sure with anything there is a margin for error how much remains to be seen. I have been using this thing on other vehicles my Vette that I traded in for my 04 Cpe. I did take my vette to IRP here in Indy and the times recorded are in line with what the Bell unit was giving me. This particular unit allows you to enter everything there is to know about the vehicle except for the mods. It really is AWSOME I would reccomend it to anyone

 

The FX1 is total garbage. The FX2 Vector is more reliable,and as far as running times a second slower than what the unit says. You need a new unit.

 

Dude you have to get FX2 it allows you to recalbrate the unit anytime you want in order to insure that the unit is workin properly.

 

Mine has that too, the only difference is that fx2 holds more runs in the memory and has the hp thingy and allows for downloads to the pc. As far as what the company themselves say.

Crawford Plenum / Z tube + Stillen Hi-Flow / Borla Dual Exhaust / Stillen Xdrilled+Stotted Rotors
Best 1/4 mile 14.469 @ 97.61, 60ft 2.399

 

the auto Gs are suppost to run a 6 flat. I dont know what mine runs but i would say its around 6 and i think 5.7 is fast. My car ran 14.6 with snow tire so with my 18s i should have no problem getting to 60 in 6. but its hard to say

 

<blockquote><font class="small">In reply to:</font><hr>

That is not correct unless you are talking about stock.

<hr></blockquote>

That was what the original poster was asking about...