Is my alignment decent?
Is my alignment decent?
I just installed my f/r spc camber kits aswell as my 350z tein stechs how do my alignment specs looks this was done 2days after the installation I have the lift time alignment so I will be going back. The only problem I see is the right front they could only make it -1.6 is that bad?
old specs
left front -2.3camber 8.3caster 0.07toe
front 0.19 total toe -0.02 steer ahead
right front -2.1camber 9.4caster 0.12toe
left rear -2.0camber 1.04toe
rear -1.02total toe 1.56 trust angle
right rear -4.3camber -2.07toe
new specs
left front -0.9camber 8.6caster 0.02toe
front 0.10 total toe -0.03 steer ahead
right front -1.6camber 8.8caster 0.08toe
left rear -1.6camber 0.08toe
rear 0.24total toe -0.04 trust angle
right rear -1.9camber 0.16toe
thanks guys! Just checkin..
old specs
left front -2.3camber 8.3caster 0.07toe
front 0.19 total toe -0.02 steer ahead
right front -2.1camber 9.4caster 0.12toe
left rear -2.0camber 1.04toe
rear -1.02total toe 1.56 trust angle
right rear -4.3camber -2.07toe
new specs
left front -0.9camber 8.6caster 0.02toe
front 0.10 total toe -0.03 steer ahead
right front -1.6camber 8.8caster 0.08toe
left rear -1.6camber 0.08toe
rear 0.24total toe -0.04 trust angle
right rear -1.9camber 0.16toe
thanks guys! Just checkin..
you should go back and tell them to do it right.
.9 and 1.6 in the front? are you kidding me? i actually have the exact same setup as you, 350z Stechs with SPC f/r camber kits so i thought i would reply here and help you out. go back and tell them to do it right!!!
the guy i took it to got it to -1.3 camber in the front -both sides-, which is exactly where i wanted him to put it (boundary of factory specs). i have no idea how they messed up with -.9 and -1.6 but that is shady lol.
and i think i went -1.6 camber in the rear, both sides, but he may have been off by 0.1 on one of the sides. alot closer together than -1.6 and -1.9 tho. he also put total toe at 0.1 in the rear. (0.05 on both sides.)
anyways, they can do much better with the parts you have installed. good luck
.9 and 1.6 in the front? are you kidding me? i actually have the exact same setup as you, 350z Stechs with SPC f/r camber kits so i thought i would reply here and help you out. go back and tell them to do it right!!!
the guy i took it to got it to -1.3 camber in the front -both sides-, which is exactly where i wanted him to put it (boundary of factory specs). i have no idea how they messed up with -.9 and -1.6 but that is shady lol.
and i think i went -1.6 camber in the rear, both sides, but he may have been off by 0.1 on one of the sides. alot closer together than -1.6 and -1.9 tho. he also put total toe at 0.1 in the rear. (0.05 on both sides.)
anyways, they can do much better with the parts you have installed. good luck
Registered User
iTrader: (10)
Joined: Jul 2006
Posts: 3,942
Likes: 7
From: PNW in Washington
6MT Coupe
^Agree 1000%. Cookie cutter alignment shops don't think about aligning equal as possible on L/R. As long as it's in the 'wide' factory specs, they think it's good enough.
OP: imo, it's a redo.
OP: imo, it's a redo.
Thanks guys I have the lifetime so I will be going back in a week or so while it settles a little more. I didn’t install the front spc a arm shim kit maybe I’ll install that before I go back for more adjustment but I believe with the 350z tein s techs its not necessary?
Thread
Thread Starter
Forum
Replies
Last Post
THMotorsports
Suspension-Vendor
257
Dec 18, 2018 05:43 PM
