G35 Coupe V35 2003 - 07 Discussion about the 1st Generation V35 G35 Coupe

windows not going down. windshield sprayers

Thread Tools
 
Search this Thread
 
Rate Thread
 
Old Jan 9, 2016 | 02:40 PM
  #1  
Dallsinghjr1's Avatar
Thread Starter
|
Registered User
Joined: Mar 2014
Posts: 24
Likes: 2
windows not going down. windshield sprayers

So at first it was just the drivers side window, and now it's both. They don't go down unless I hold the button and bang the door once simultaneously. They go down easy, but struggle to go back up. I have to grab it and pull up while holding the button. I'm assuming it's the motors, but can anyone give me some advice on it? Or tell me where is the best place to get the motors without spending $250 each at the dealership.

Another thing is the windshield sprayers don't work. Me and brother disconnected the line and blew through it and the liquid came out through the nozzles on the wipers, so it's not clogged. Probably the pump...?
 
Reply
Old Jan 9, 2016 | 02:47 PM
  #2  
Urbanengineer's Avatar
Super Moderator
10 Year Member
Liked
Community Favorite
iTrader: (3)
Joined: Jun 2013
Posts: 11,174
Likes: 1,044
From: OH-IO
Premier Member

When I took off my wipers for repaint last time I kinked the line when reinstalling them. Check your paths.
 
Reply
Old Jan 9, 2016 | 03:38 PM
  #3  
Dallsinghjr1's Avatar
Thread Starter
|
Registered User
Joined: Mar 2014
Posts: 24
Likes: 2
We blew through the lines and they weren't kinked because the residual fluids came through. So what else can it be?
Originally Posted by Urbanengineer
When I took off my wipers for repaint last time I kinked the line when reinstalling them. Check your paths.
 
Reply
Old Jan 13, 2016 | 10:44 PM
  #4  
Peckols's Avatar
Registered User
Joined: Oct 2015
Posts: 26
Likes: 0
sub'd
my squirters also don't squirt
 
Reply
Old Jan 13, 2016 | 11:42 PM
  #5  
hurleyguys's Avatar
Registered User
iTrader: (9)
Joined: Feb 2009
Posts: 1,008
Likes: 43
From: 310 Socal
OP if you are good with a soldering gun replace the brushes in the window motor. its easy to do.

as for the windshield wiper fluid. not sure. check the tubing to make sure there are no holes in it and free of debris. prob the pump on the reservoir tank.
 
Reply
Old Jan 14, 2016 | 05:10 AM
  #6  
partyman66's Avatar
Registered User
iTrader: (1)
Joined: Jul 2004
Posts: 3,560
Likes: 228
From: Southeastern Mass.
Pull your window motors and remove the central drive shaft from them. Clean everything up in there and remove excess carbon, grease the shaft and reassemble and reinstall. Did that on my drivers side windows 2 years ago and it's been going strong since then.
 
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
aznvictobear
Exterior - Body Parts
1
Feb 7, 2016 10:32 PM
Carlos Chavez
Interior
3
Jan 13, 2016 12:11 PM
Ayyston
Interior & Exterior
0
Jan 7, 2016 05:54 PM
35reilly
Engine - Complete Motors
0
Dec 14, 2015 05:49 PM



You have already rated this thread Rating: Thread Rating: 0 votes,  average.


All times are GMT -4. The time now is 01:45 AM.