for those who don't care for OEM spoilers
Thread Starter
|
Registered User
Joined: Nov 2008
Posts: 120
Likes: 0
From: san francisco
for those who don't care for OEM spoilers
PM me if anyone interested to do this (Chrome Delete) ...
I can also do side mirror number (2)
I guess I can't handle that many PMs anymore haha.... here is the deal:
1) follow the instructions to remove the pieces you want to wrap
2) mail me the parts
3) I will wrap it and mail it back to you
4) the wrapping require NO CUTTING or damage your original pieces and you can always remove it with heat
(wrapping the side mirrors also mean protecting it against chips/flying rocks from driving)
about removing your chrome piece:
first tape around the lip and cover with cloths so you won't scratch anything
1) open ur trunk
2) remove all push pins that holds the lining
3) remove 4 hex nuts on the back of lip location (middle edge of the trunk)
4) there are 2 push in pins from lip to trunk each ends
(you should be able to pop out the lip now)
Do not pull too hard!!!!
there are wires for trunk switch & rearview camera
5) remove screws that holds the rearview camera & trunk switch assemble.
6) push trunk switch to slid it out
7) DONE
Please PM me for any questions and I will PM you my email if you are interested. Paypal payment is recommended
Pls understand I don't stock those materials since they are not cheap, but I will stock them if demand gets higher.
I will let you know when you should ship them to me, to minimize the time for you to get it back on to your car.
I can also do side mirror number (2)
I guess I can't handle that many PMs anymore haha.... here is the deal:
1) follow the instructions to remove the pieces you want to wrap
2) mail me the parts
3) I will wrap it and mail it back to you
4) the wrapping require NO CUTTING or damage your original pieces and you can always remove it with heat
(wrapping the side mirrors also mean protecting it against chips/flying rocks from driving)
about removing your chrome piece:
first tape around the lip and cover with cloths so you won't scratch anything
1) open ur trunk
2) remove all push pins that holds the lining
3) remove 4 hex nuts on the back of lip location (middle edge of the trunk)
4) there are 2 push in pins from lip to trunk each ends
(you should be able to pop out the lip now)
Do not pull too hard!!!!
there are wires for trunk switch & rearview camera
5) remove screws that holds the rearview camera & trunk switch assemble.
6) push trunk switch to slid it out
7) DONE
Please PM me for any questions and I will PM you my email if you are interested. Paypal payment is recommended
Pls understand I don't stock those materials since they are not cheap, but I will stock them if demand gets higher.
I will let you know when you should ship them to me, to minimize the time for you to get it back on to your car.
Last edited by ultraman1017; Nov 1, 2010 at 02:39 PM.
DI-NOC - http://solutions.3m.com/wps/portal/3...s/Di-Noc-Film/
Where people usually buy them - http://www.carbonfiberfilm.com/
Where people usually buy them - http://www.carbonfiberfilm.com/
Trending Topics
Thread Starter
|
Registered User
Joined: Nov 2008
Posts: 120
Likes: 0
From: san francisco
maybe it's just shadow, it is original trunk finish cover with CF overlay. I did check the gaps between trunk and the finish lip with a piece of paper, I can't get anything in between them. 
Thread Starter
|
Registered User
Joined: Nov 2008
Posts: 120
Likes: 0
From: san francisco
I detached it and wrap, this is the only way you can get the best alignment and seal tight with no water leaking in to camera and trunk switch.
Last edited by ultraman1017; May 16, 2010 at 10:52 PM.
