General Tech Questions This Forum is Only for Questions and Posts that Do Not fit under the other Tech categories.(No Classified Posts)

Car Will Not Start Up...Please Help

Thread Tools
 
Search this Thread
 
Rate Thread
 
Old Nov 13, 2011 | 02:19 PM
  #1  
blackhat5's Avatar
Thread Starter
|
Premier Member
Joined: Sep 2009
Posts: 43
Likes: 0
Premier Member

Car Will Not Start Up...Please Help

Hi guys. I have a 2005 G35 Coupe A/T and when I woke up this morning, my car would start, but the following lights displayed on the dash:

VDC OFF
ABS
SLIP

When I tried to push on the brake pedal and switch it into drive, the shifter **** is completely locked.

I read on here to check the fuses for the rear brake lights, and low and behold, the fuse was blown. So, I replace it, and now the brake lights are fine, but the car won't start at all now.

I checked the engine bay fuses, all seem fine. I also disconnected both battery cables to reset the computer, and that did not help either.

When I switch the key to the ON position, I hear two "knocking" sounds in the engine, which I was told is normal.

I guess I am confused as so why the car started this morning, and then once changing the fuse out, it will not start at all now.

Any help would grealty be appreciated, as now I cannot get my daily driver to start at all.

Thanks a million!
 
Reply
Old Nov 13, 2011 | 02:56 PM
  #2  
blackhat5's Avatar
Thread Starter
|
Premier Member
Joined: Sep 2009
Posts: 43
Likes: 0
Premier Member

Just an update, we tried jump starting the car and it will not start or turnover either.
 
Reply
Old Nov 13, 2011 | 02:56 PM
  #3  
Texasscout's Avatar
Registered User
iTrader: (11)
Joined: Feb 2005
Posts: 35,605
Likes: 2,116
From: South Texas
will it start if you pull the fuse back out?
 
Reply
Old Nov 13, 2011 | 03:02 PM
  #4  
blackhat5's Avatar
Thread Starter
|
Premier Member
Joined: Sep 2009
Posts: 43
Likes: 0
Premier Member

No.

Now, the owner's manual showed the fuses in the engine bay, and we took out one box fuse that held fuses for the vdc, abs, etc. and when we put that back in, is when the car wouldn't start. Sorry I might have explained the process incorrectly.
 
Reply
Old Nov 13, 2011 | 03:09 PM
  #5  
blackhat5's Avatar
Thread Starter
|
Premier Member
Joined: Sep 2009
Posts: 43
Likes: 0
Premier Member

Also when I turn the car to the ON position, the lights inside light up, but when i try to start it, all the lights go off until I switch it back to the ON position.
 
Reply
Old Nov 13, 2011 | 04:14 PM
  #6  
Texasscout's Avatar
Registered User
iTrader: (11)
Joined: Feb 2005
Posts: 35,605
Likes: 2,116
From: South Texas
That's normal, all power is directed to the starter when it is energized.

You must have something out of whack with the computer. See if you can borrow an OBD2 reader and check for a code. That would be a good starting place.
 
Reply
Old Nov 13, 2011 | 05:52 PM
  #7  
blackhat5's Avatar
Thread Starter
|
Premier Member
Joined: Sep 2009
Posts: 43
Likes: 0
Premier Member

Ok thanks I'll try that.
 
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
chinee
G35 Sedan V35 2003-06
21
Jun 10, 2024 07:48 PM
newg37
G35 Coupe V35 2003 - 07
1
Jul 26, 2015 09:32 AM
itschuckster
G35 Sedan V35 2003-06
2
Jul 25, 2015 08:07 AM
kenthung
G35 Coupe V35 2003 - 07
0
Jul 21, 2015 05:56 AM
realtalk21
G35 Cars
4
Jul 20, 2015 09:07 AM



You have already rated this thread Rating: Thread Rating: 0 votes,  average.


All times are GMT -4. The time now is 05:19 PM.