Removing Shift knob and trim around it??
#1
05-27-2003, 07:06 PM
Join Date: Apr 2003
Location: Baton Rouge, LA
Posts: 92
Likes: 0
Received 0 Likes
on
0 Posts
#2
05-27-2003, 08:11 PM
Re: Removing Shift **** and trim around it??
Is the G35 coupe's shifter the same as the 350Z's? If it is, this will help:http://www.rallitec.com/Q-shifter/
#4
05-28-2003, 04:53 PM
Join Date: Apr 2003
Location: Baton Rouge, LA
Posts: 92
Likes: 0
Received 0 Likes
on
0 Posts
#5
05-28-2003, 05:44 PM
<font color=green>GSM</font color=green>
#6
05-28-2003, 07:14 PM
Join Date: Apr 2003
Location: Baton Rouge, LA
Posts: 92
Likes: 0
Received 0 Likes
on
0 Posts
#7
05-28-2003, 08:19 PM
Re: Removing Shift **** and trim around it??
<blockquote><font class="small">In reply to:</font><hr>
The ESM says to twist counterclockwise. It will come off.
<hr></blockquote>
For the avoidance of any confusion, those instructions are only for the MT. For the AT, you need to pull the ring at the bottom down and then remove the exposed clip.
No idea how to do the trim on the MT. If anyone wants to remove the AT's plate, be advised that you'll need to unscrew stuff from underneath it.
-Jack
Obsidian/graphite '03 Coupe premium nav
The ESM says to twist counterclockwise. It will come off.
<hr></blockquote>
For the avoidance of any confusion, those instructions are only for the MT. For the AT, you need to pull the ring at the bottom down and then remove the exposed clip.
No idea how to do the trim on the MT. If anyone wants to remove the AT's plate, be advised that you'll need to unscrew stuff from underneath it.
-Jack
Obsidian/graphite '03 Coupe premium nav
Trending Topics
#8
05-28-2003, 08:25 PM
<font color=green>GSM</font color=green>
#9
05-28-2003, 09:20 PM
Re: Removing Shift **** and trim around it??
Remove shift **** first, turn counterclockwise. Stick your fingers through the leather on the bottom part of the shift boot. Pull up, it's held in with clips. Don't pull too hard because the hazard light harness is still attached to that piece. Good, luck, only thing to watch out for is the shifter without the **** on. It might scratch the lower console piece if you're not carefull.
#10
05-28-2003, 10:21 PM
Join Date: Apr 2003
Location: Baton Rouge, LA
Posts: 92
Likes: 0
Received 0 Likes
on
0 Posts
Re: Removing Shift **** and trim around it??
hey. I have the ESM also but it doesn't really say much. I find it rather crappy. Please send me what you found though. Maybe I'm seeing something different. thanks.......email is kyleinbrla@yahoo.com
#11
06-06-2003, 02:08 PM
G SQUAD
Join Date: May 2003
Location: Long Island
Posts: 1,060
Likes: 0
Received 0 Likes
on
0 Posts
Re: Removing Shift **** and trim around it??
I don't know if you still need help, but all you do is pull up on the rear of the trim inside the leather boot and the rear will pop up. Then you pull off completely, but like someone else said, just make sure to unplug the hazard and ash tray wires.
2003.5 - G35 6spd - Diamond Graphite/Graphite leather, prem, aero package/kit
2003.5 - G35 6spd - Diamond Graphite/Graphite leather, prem, aero package/kit
#12
06-06-2003, 05:10 PM
Join Date: Apr 2003
Location: Baton Rouge, LA
Posts: 92
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
RemmyZero
V36 DIY
10
04-23-2018 11:13 AM
