MREV2 and Tune Question - Tuning Gurus Welcome

Thread Tools
 
Search this Thread
 
Rate Thread
 
Old Sep 20, 2012 | 11:29 AM
  #1  
PAIXAO's Avatar
Thread Starter
|
Registered User
iTrader: (14)
Joined: Sep 2008
Posts: 8,338
Likes: 445
From: The Commonwealth
MREV2 and Tune Question - Tuning Gurus Welcome

I am currently Osiris tuned and I recently picked up a MREV2. Basically I am wondering if I can install it and hold off on a re-tune until I install my HFC. I'm looking at probably a 30-60 day time period in which my car will be driven approximately 2k-4k miles. I will schedule a re-tune within 1 week of installing the HFC.

Current engine mods on my 2004 Sedan 6MT:

Stillen Cat Back Exhaust
Motordyne 5/16 Spacer
Stillen Short Ram Intake
Uprev Osiris Tune

Thanks
 
Reply
Old Sep 20, 2012 | 11:45 AM
  #2  
Texasscout's Avatar
Registered User
iTrader: (11)
Joined: Feb 2005
Posts: 35,605
Likes: 2,116
From: South Texas
I thought the MREV2 was ONLY for the 05'-06' "Rev Up" motor?
 
Reply
Old Sep 20, 2012 | 11:56 AM
  #3  
PAIXAO's Avatar
Thread Starter
|
Registered User
iTrader: (14)
Joined: Sep 2008
Posts: 8,338
Likes: 445
From: The Commonwealth
There have been proven gains using both the MREV2 and the 5/16 spacer on the nonrev motor. On a cost basis, its not worth it for most, but I got a good deal on this MREV2 and I couldn't pass it up.

If you give me a sec I will find a dyno chart reflecting gains on a nonrev sedan.
 
Reply
Old Sep 20, 2012 | 11:59 AM
  #4  
PAIXAO's Avatar
Thread Starter
|
Registered User
iTrader: (14)
Joined: Sep 2008
Posts: 8,338
Likes: 445
From: The Commonwealth
Name:  April31Plot5-1.gif
Views: 39
Size:  55.8 KB

As you can see, it does help in the low end of the spectrum. These gains are before a tune, which should correct the 4500-5500 rpm range and provide further gains throughout.
 

Last edited by PAIXAO; Sep 20, 2012 at 12:09 PM.
Reply
Old Sep 20, 2012 | 12:04 PM
  #5  
Texasscout's Avatar
Registered User
iTrader: (11)
Joined: Feb 2005
Posts: 35,605
Likes: 2,116
From: South Texas
I know it made a real "butt dyno" difference in my 05' sedan.
 
Reply
Old Sep 20, 2012 | 12:59 PM
  #6  
seymore4's Avatar
Premier Member
15 Year Member
Liked
Loved
Community Favorite
iTrader: (114)
Joined: Mar 2009
Posts: 4,972
Likes: 433
From: West coast
m56
Premier Member

you will be fine
 
Reply
Old Sep 20, 2012 | 01:48 PM
  #7  
PAIXAO's Avatar
Thread Starter
|
Registered User
iTrader: (14)
Joined: Sep 2008
Posts: 8,338
Likes: 445
From: The Commonwealth
Originally Posted by seymore4
you will be fine
Thanks Joe. My main concern is that the additional air flow will adjust my MAF curve or fuel compensation table to unacceptable rich/lean conditions.
 
Reply
Old Sep 20, 2012 | 02:01 PM
  #8  
seymore4's Avatar
Premier Member
15 Year Member
Liked
Loved
Community Favorite
iTrader: (114)
Joined: Mar 2009
Posts: 4,972
Likes: 433
From: West coast
m56
Premier Member

It will throw it off a little, but no where near dangerous levels
 
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
jsimonk
General Media Share
17
Dec 22, 2023 03:49 PM
poktanG35
Engine - Exhaust
23
Oct 26, 2015 03:32 AM
LilWest209
Tuner & Dyno
6
Aug 24, 2015 02:00 PM
G35Sask
Intake & Exhaust
16
Aug 5, 2015 10:17 PM
sick_sixspeed
Tuner & Dyno
10
Jul 21, 2015 03:23 AM



You have already rated this thread Rating: Thread Rating: 0 votes,  average.


All times are GMT -4. The time now is 04:00 AM.