Alignment done perfect without a-arms!!
#16
i have to agree. If you're really bendings arms, it will not only
compromise the integrety, it will void warranty, and will alter the
rotation path of the arm when it compresses resulting in distorted
suspension geometry.
Just get the right parts to get the job done right or leave it stock
if you're so caught up on stock alignment measurements.
compromise the integrety, it will void warranty, and will alter the
rotation path of the arm when it compresses resulting in distorted
suspension geometry.
Just get the right parts to get the job done right or leave it stock
if you're so caught up on stock alignment measurements.
Originally Posted by dklau33
I'm sure it works and I'm just speaking from initial impressions without any real knowledge of how it works. But my assumption is that bending parts may compromise structural integrity of said parts. That's where my comment stemmed from. But like I said, it's all an assumption. Until someone can tell me what is exactly done then it's just an initial comment so take it with a grain of salt.
#18
Originally Posted by kenchan
If you're really bendings arms, it will not only
compromise the integrety, it will void warranty, and will alter the
rotation path of the arm when it compresses resulting in distorted
suspension geometry.
compromise the integrety, it will void warranty, and will alter the
rotation path of the arm when it compresses resulting in distorted
suspension geometry.
Just get the right parts to get the job done right or leave it stock
if you're so caught up on stock alignment measurements.
if you're so caught up on stock alignment measurements.
![Smilie](https://g35driver.com/forums/images/smilies/smile.gif)
Who are you to tell this guy how to modify his car?
#19
Originally Posted by Moog
What exactly are the alignment specs that Infiniti deems "within range"? I would say they were perfect if everything fell within range.
Gsedan35 posted the specs on both the coupes and sedans and
his recommendations as well for sedan.
but, what you're saying is that for example, if the toe range is
0 to .22 per side and total toe of .44 on the rear, it could look
like this and still be considered 'perfect' ... I don't think so.
R toe 0.00 (within range)
L toe 0.22 (within range)
Total Toe: 0.22 (within range)
The car would be wandering on each bump on the right side and
thrust angle will be pretty bad.
There are some bias to each car especially if it had been in an
accident or chassis tweaked...perhaps suhki's car is tweaked
and the mechanic hand to compensate to minimize thrust
angle.
#21
Originally Posted by Moog
And I don't understand the pessimistic attitude you're giving off regarding this guys attempt at getting his alignment back to tolerable numbers. It's a great alternative to aftermarket parts, it worked for him, and he's happy. ![Smilie](https://g35driver.com/forums/images/smilies/smile.gif)
Who are you to tell this guy how to modify his car?
![Smilie](https://g35driver.com/forums/images/smilies/smile.gif)
Who are you to tell this guy how to modify his car?
As my post above, there is a difference between "perfect alignment" and
"within specs."
The guy's alignment might be within factory tolerance, but it is not perfect.
but again, his car might have some bias and the tech may have had to
compensate.
Who am I? A person that is taking this post and mentioning there is a
difference between a perfect alignment or just being within tolerance.
I really don't care if he did or didn't use aftermarket parts. My point
is that there is a difference between a perfect and within tolerance
aligment results. that's all.
And sorry if I spoiled the party. Im happy that the guy is happy with his
car. But if it was my car, that toe-in is not acceptable.
#22
Sure we can nitpick at his use of perfect not meaning the same to you, but this guy is happy with what he had done. Let's not rain on his parade and make him second guess the work he's had done.
FYI...from what I've been told by an alignment technician, slight toe-in is usually dialed in to keep the car driving straight.
FYI...from what I've been told by an alignment technician, slight toe-in is usually dialed in to keep the car driving straight.
#23
Agreed! ![Smilie](https://g35driver.com/forums/images/smilies/smile.gif)
Yes, toe-in adds in-line stability. But it needs to be equal or
close to on both sides.
imho and from experience, proper toe-in is more important than
getting the camber perfectly equal on both sides.
![Smilie](https://g35driver.com/forums/images/smilies/smile.gif)
Yes, toe-in adds in-line stability. But it needs to be equal or
close to on both sides.
imho and from experience, proper toe-in is more important than
getting the camber perfectly equal on both sides.
Originally Posted by Moog
Sure we can nitpick at his use of perfect not meaning the same to you, but this guy is happy with what he had done. Let's not rain on his parade and make him second guess the work he's had done.
FYI...from what I've been told by an alignment technician, slight toe-in is usually dialed in to keep the car driving straight.
FYI...from what I've been told by an alignment technician, slight toe-in is usually dialed in to keep the car driving straight.
#24
Originally Posted by kenchan
imho and from experience, proper toe-in is more important than
getting the camber perfectly equal on both sides.
getting the camber perfectly equal on both sides.
live and learn...
#25
Originally Posted by Moog
I know this all too well. I've installed camber kits on my previous cars. Camber came back into a reasonable spec on my Accord, but I did not get a proper alignment immediately after the installation. Toe was waaaay off, and I had a set of brand new 18" tires wear out in 2 months.
live and learn...
live and learn...
hehehe, yeah, plus the car doesn't handle too well with improper
toe settings. Ive already taken my G in for numerous alignments to
dial-in what i want out of this car...
![Smilie](https://g35driver.com/forums/images/smilies/smile.gif)
Thread
Thread Starter
Forum
Replies
Last Post
THMotorsports
Suspension-Vendor
257
12-18-2018 05:43 PM
FS[NorWest]: 04 OEM Faceplate and CD/Tape Unit
Oregon13
Audio/Video/Electronics
5
03-01-2016 12:06 AM
FS[SoCal]: D/S 4080 Enclosure & JL Audio W6v2 10 inch
MrIP35
Audio/Video/Electronics
9
11-08-2015 10:47 AM