G35Driver - Infiniti G35 & G37 Forum Discussion
0 2016/08/27 21:16:54
0 2016/08/27 21:18:09
0 2016/08/27 21:19:24
Yes...I have #PorscheEnvy One of these years I'll come across a 964 I can afford..but til then I have my GT35RS project :) ..now for some paint...
Yes...I have #PorscheEnvy One of these years I'll come across a 964 I can afford..but til then I have my GT35RS project :) ..now for some paint...
0 2016/08/27 21:20:01
Stripped, taped off and waiting.
Stripped, taped off and waiting.
0 2016/09/26 18:29:18
Center of the hood under the masking will remain cf. Outer sides will be Laser Red.
Center of the hood under the masking will remain cf. Outer sides will be Laser Red.
0 2016/09/26 18:31:14
Placement is still being decided. Can't build the front support bar without the car here though..
Placement is still being decided. Can't build the front support bar without the car here though..
0 2016/09/26 18:33:13
0 2016/09/26 18:35:13
The cover came with the lights..just a picture. Only time I'd use them is maybe on a long hwy trip.
The cover came with the lights..just a picture. Only time I'd use them is maybe on a long hwy trip.
0 2016/09/26 18:36:41
Much better...but still not clean yet.
Much better...but still not clean yet.
0 2016/10/14 13:46:19
Finally washed it and goo gone'd the hood with the masking tape residue.
Finally washed it and goo gone'd the hood with the masking tape residue.
0 2016/10/18 00:38:47
0 2016/10/18 00:39:38
Installed the front fender liners also. Go Rockauto.com
Installed the front fender liners also. Go Rockauto.com
0 2016/10/18 00:40:47
0 2016/10/26 23:07:33
0 2016/10/26 23:08:46
0 2016/10/26 23:09:42
0 2016/10/31 22:40:42
0 2016/10/31 22:41:18
0 2016/10/31 22:42:07
0 2016/10/31 22:42:39
The AMS pulleys are OEM size, so not underdriving any accessories, but about 1/4 the weight, except for the crank pulley obviously. I wish I had weighed them both before installing. The result in lost rotational weight gives back the hp that was being used to carry the weight. I'm keeping a close eye and ear on the engine bc of the removal of the harmonic balancer. No issues or resonance thus far.
The AMS pulleys are OEM size, so not underdriving any accessories, but about 1/4 the weight, except for the crank pulley obviously. I wish I had weighed them both before installing. The result in lost rotational weight gives back the hp that was being used to carry the weight. I'm keeping a close eye and ear on the engine bc of the removal of the harmonic balancer. No issues or resonance thus far.
0 2016/10/31 22:43:12
0 2016/10/31 22:47:45
This little piece of plastic will ruin your day. The shoe for the chain guide and the timing chain tensioner. I broke a tab off, luckily it popped out and not into the timing cover. Luckily again I have a local buddy that drifts a G sedan and had a few spare engines. The one I got from him looks much newer and far less worn than mine.
This little piece of plastic will ruin your day. The shoe for the chain guide and the timing chain tensioner. I broke a tab off, luckily it popped out and not into the timing cover. Luckily again I have a local buddy that drifts a G sedan and had a few spare engines. The one I got from him looks much newer and far less worn than mine.
0 2016/10/31 22:48:13
The piece goes here.
The piece goes here.
0 2016/10/31 22:51:51
Tucked nicely in the back
Tucked nicely in the back
0 2016/10/31 22:52:56
0 2016/10/31 22:54:17
Pays to read the FSM for the procedure you want to do first. I know this but, should have done it long ago to be prepared. The top pulley I thought was the water pump, it is just an idler. The WP is run off the timing chain. Oh well..done now.
Pays to read the FSM for the procedure you want to do first. I know this but, should have done it long ago to be prepared. The top pulley I thought was the water pump, it is just an idler. The WP is run off the timing chain. Oh well..done now.
0 2016/10/31 22:54:49
0 2016/10/31 22:58:36
Fits perfectly, no trimming and a simple bracket. Same lines off the valve covers (PCV on passenger side, and vent on rear drivers side) and one out to the intake.
Fits perfectly, no trimming and a simple bracket. Same lines off the valve covers (PCV on passenger side, and vent on rear drivers side) and one out to the intake.
0 2016/10/31 22:59:24
Clutch throw out arm pivot bolt
Clutch throw out arm pivot bolt
0 2016/11/11 19:56:28
0 2016/11/30 18:29:45
0 2016/11/30 18:30:12
And that is how she has sat for about 3 weeks.
And that is how she has sat for about 3 weeks.
0 2016/11/30 18:30:43
0 2016/12/01 09:24:55
WTF?!
WTF?!
0 2016/12/01 09:25:07
Buhh bye
Buhh bye
0 2016/12/01 09:26:37
Driver side motor mount came apart in my hands when I took it out. good time to replace them. I took out the long tube headers because they kept me from getting the last transmission out and made a mess. Installed some shorty headers that are wrapped with resonated test pipes.
Driver side motor mount came apart in my hands when I took it out. good time to replace them. I took out the long tube headers because they kept me from getting the last transmission out and made a mess. Installed some shorty headers that are wrapped with resonated test pipes.
0 2016/12/01 09:28:12
0 2016/12/01 09:30:17
This is how she sat for days.
This is how she sat for days.
0 2016/12/01 09:31:36
Broken right hand
Broken right hand
0 2016/12/01 09:32:48