G35Driver - Infiniti G35 & G37 Forum Discussion
0 2017/05/18 17:37:30
0 2017/05/18 17:44:30
0 2017/05/18 17:44:41
0 2017/05/18 17:44:49
0 2017/05/18 17:47:41
0 2017/05/18 17:47:49
Getting her ready to go onto the engine stand
Getting her ready to go onto the engine stand
0 2017/05/18 17:51:52
FAST 102
FAST 102
0 2017/05/18 17:52:05
Most of the headlight tabs were broken so new headlights will be going in
Most of the headlight tabs were broken so new headlights will be going in
0 2017/05/18 17:56:56
The radiator support was cracked in a few places so a new one will be replacing it
The radiator support was cracked in a few places so a new one will be replacing it
0 2017/05/18 17:57:32
0 2017/05/18 17:57:49
The motor only needed a little bit of exterior cleaning
The motor only needed a little bit of exterior cleaning
0 2017/05/18 18:00:31
LS6 Valley Cover
LS6 Valley Cover
0 2017/05/18 18:00:41
Knock sensors installed
Knock sensors installed
0 2017/05/18 18:00:50
The rear rotors practically fell apart after needing a hammer to get them off
The rear rotors practically fell apart after needing a hammer to get them off
0 2017/05/18 18:04:50
The lower steering shaft U-joint is getting replaced
The lower steering shaft U-joint is getting replaced
0 2017/05/18 18:05:04
OEM clutch master cylinder and lines getting replaced with a Wilwood unit
OEM clutch master cylinder and lines getting replaced with a Wilwood unit
0 2017/05/18 18:05:14
New bearings and hubs will be installed
New bearings and hubs will be installed
0 2017/05/18 18:05:29
0 2017/05/18 18:07:52
0 2017/05/18 18:08:20
Nice corrosion forming in the knuckle around where the bearing sat
Nice corrosion forming in the knuckle around where the bearing sat
0 2017/05/18 18:08:29
One side of the front almost completely apart
One side of the front almost completely apart
0 2017/05/18 18:09:15
0 2017/05/18 18:12:09
S13 gas pedal bolts right up
S13 gas pedal bolts right up
0 2017/05/18 18:13:32
Lots of work still to go
Lots of work still to go
0 2017/05/18 18:15:30
Old rack and pinion ready to be shipped back for a core
Old rack and pinion ready to be shipped back for a core
0 2017/05/18 18:15:50
New rack and pinion patiently waiting
New rack and pinion patiently waiting
0 2017/05/18 18:15:58
SIKKY oil pan looks and fits great
SIKKY oil pan looks and fits great
0 2017/05/21 14:59:47
WS harness and grounding kit
WS harness and grounding kit
0 2017/05/21 15:01:46
Outer tie rod ends, cabin air filter, parking brake shoes and hardware, wiper blades, and new front side markers
Outer tie rod ends, cabin air filter, parking brake shoes and hardware, wiper blades, and new front side markers
0 2017/05/21 15:03:31
Steering shaft U-joint, rack and pinion bushings, bearing & race driver set (for the chassis bushings), and CJM fuel return parts
Steering shaft U-joint, rack and pinion bushings, bearing & race driver set (for the chassis bushings), and CJM fuel return parts
0 2017/05/21 15:05:12
For what this thing cost, it's going to pay for itself real quick
For what this thing cost, it's going to pay for itself real quick
0 2017/05/28 18:38:18
0 2017/05/28 18:38:26
0 2017/05/28 18:39:42
Rack bushings pressed out
Rack bushings pressed out
0 2017/05/28 18:39:51
New poly bushings ready to go in
New poly bushings ready to go in
0 2017/05/28 18:40:25
Lubed them up and they slid right in
Lubed them up and they slid right in
0 2017/05/28 18:40:33
I think LS engines from '01 only have the front tubes installed from the factory.
I think LS engines from '01 only have the front tubes installed from the factory.
0 2017/05/28 18:43:12
Aftermarket front and rear steam vent lines
Aftermarket front and rear steam vent lines
0 2017/05/28 18:43:20
I wanted some extra peace of mind so I am using all four.
I wanted some extra peace of mind so I am using all four.
0 2017/05/28 18:43:27