G35Driver - Infiniti G35 & G37 Forum Discussion
Finally got the 4 nuts loose without breaking anything. Subframe on the way down
Finally got the 4 nuts loose without breaking anything. Subframe on the way down
0 2017/12/03 14:24:40
Ready for poly differential and subframe bushings. Gonna change the axle seals and the cover gasket while it's out.
Ready for poly differential and subframe bushings. Gonna change the axle seals and the cover gasket while it's out.
0 2017/12/03 14:25:46
The 18x8's came in. Gotta get some new TPMS sensors then have the winter tires put on
The 18x8's came in. Gotta get some new TPMS sensors then have the winter tires put on
0 2017/12/04 14:35:50
Got the core support trimmed enough to fit the radiator. It's a rough fit for now. I'll finish up with some better Dremel work to smooth out the sharp edges. I think I have a good idea on how to get it mounted permanently
Got the core support trimmed enough to fit the radiator. It's a rough fit for now. I'll finish up with some better Dremel work to smooth out the sharp edges. I think I have a good idea on how to get it mounted permanently
0 2017/12/04 14:37:11
Not a whole lot of clearance but everything fits without rubbing. I may try switching to CTS accessories in the future for extra room. The bottom hose should be fun and try to match up.
Not a whole lot of clearance but everything fits without rubbing. I may try switching to CTS accessories in the future for extra room. The bottom hose should be fun and try to match up.
0 2017/12/04 14:38:35
Got the Z1 rear differential bushing installed and 1 of the four factory subframe bushings out.
Got the Z1 rear differential bushing installed and 1 of the four factory subframe bushings out.
0 2017/12/11 14:17:56
0 2018/03/25 09:52:25
0 2018/03/25 17:31:55
0 2018/03/25 17:32:03
0 2018/03/25 17:32:12
All put back together with poly differential and subframe bushings, new axle seals, and fresh fluid
All put back together with poly differential and subframe bushings, new axle seals, and fresh fluid
0 2018/03/28 11:55:50
Factory crank pulley off
Factory crank pulley off
0 2018/03/28 11:57:28
Going to assemble the 10%UD pulley and try to get it bolted on tonight
Going to assemble the 10%UD pulley and try to get it bolted on tonight
0 2018/03/28 11:58:02
Cleaning up the terrible rusty threads so I have no issues lifting the subframe back into place
Cleaning up the terrible rusty threads so I have no issues lifting the subframe back into place
0 2018/03/29 15:01:23
All clean and covered in anti-sieze
All clean and covered in anti-sieze
0 2018/03/29 15:03:18
All bolted back into place
All bolted back into place
0 2018/03/30 14:46:22
Driveshaft on
Driveshaft on
0 2018/03/30 14:47:09
Test fitting new crank pulley and figuring out the proper belt size
Test fitting new crank pulley and figuring out the proper belt size
0 2018/03/30 14:47:52
Been about a year in the making so far. Soon....
Been about a year in the making so far. Soon....
0 2018/03/30 14:48:53
Got the driver's rear put back together - Energy Suspension bushings everywhere, Kinetic camber and toe arms, BC coils w/ Swift springs, Moog bearings and new hubs. That nasty caliper will be replaced as well.
Got the driver's rear put back together - Energy Suspension bushings everywhere, Kinetic camber and toe arms, BC coils w/ Swift springs, Moog bearings and new hubs. That nasty caliper will be replaced as well.
0 2018/03/31 15:14:03
Forgot to put the backing plate on, the rear shoes wouldn't have worked without it
Forgot to put the backing plate on, the rear shoes wouldn't have worked without it
0 2018/04/01 14:31:39
New PowerStop rotors, pads, and SS lines
New PowerStop rotors, pads, and SS lines
0 2018/04/01 14:32:40
Passenger side rear - tomorrow's project
Passenger side rear - tomorrow's project
0 2018/04/01 14:33:33
0 2018/05/02 17:48:26
Got the summer tires mounted. 265/40/18 on 18x9.5 +38 out back and 235/45/18 on 18x8.5 +35 up front
Got the summer tires mounted. 265/40/18 on 18x9.5 +38 out back and 235/45/18 on 18x8.5 +35 up front
0 2018/06/12 13:32:03
Couldn't find a pretty place to run the heater hoses.
Couldn't find a pretty place to run the heater hoses.
0 2018/06/12 13:32:12
Decided to start wrapping the headers once they were already installed 🤦
Decided to start wrapping the headers once they were already installed 🤦
0 2018/06/12 13:32:19
Didn't like the factory terminals so I installed these mil-spec ones and a distribution block for the positive terminal
Didn't like the factory terminals so I installed these mil-spec ones and a distribution block for the positive terminal
0 2018/06/12 13:32:28
Got a set of black housing eBay lights. They are just temporary. Gonna retrofit them to projectors once the car is driveable
Got a set of black housing eBay lights. They are just temporary. Gonna retrofit them to projectors once the car is driveable
0 2018/06/12 13:50:52
The WEDS look killer in the sunlight
The WEDS look killer in the sunlight
0 2018/06/12 13:51:11
Vroom Vroom
Vroom Vroom
0 2018/06/12 13:51:30
What was left of the license plate light bracket. Grabbed a new one and got it installed with LED bulbs
What was left of the license plate light bracket. Grabbed a new one and got it installed with LED bulbs
0 2018/06/12 13:51:42
Cut the top off of a 240sx pedal and welded it onto the stock G pedal. Works great with the Z32 throttle cable.
Cut the top off of a 240sx pedal and welded it onto the stock G pedal. Works great with the Z32 throttle cable.
0 2018/06/16 15:19:11
Finally got the drive it! Only about 10 feet but it was awesome.
Finally got the drive it! Only about 10 feet but it was awesome.
0 2018/06/16 15:20:36
Alignment is all out of whack and I still need to roll the rear fenders
Alignment is all out of whack and I still need to roll the rear fenders
0 2018/06/16 15:20:54
0 2018/06/16 15:21:10
1 step forward and 2 steps back. Engine and transmission back out.
1 step forward and 2 steps back. Engine and transmission back out.
0 2018/07/27 12:28:27
Ready to be shipped out for a stage 2 rebuild
Ready to be shipped out for a stage 2 rebuild
0 2018/07/27 12:29:16
Wrapping the headers is much easier when they are out of the car
Wrapping the headers is much easier when they are out of the car
0 2018/07/27 12:31:08
0 2019/02/24 15:14:03