G35Driver - Infiniti G35 & G37 Forum Discussion
0 2021/11/20 17:17:36
ICT Billet coil brackets. Going to paint the valve covers red while I have them off.
ICT Billet coil brackets. Going to paint the valve covers red while I have them off.
0 2021/11/20 11:59:56
0 2021/11/20 11:58:34
Fantastic Beer from Sixpoint
Fantastic Beer from Sixpoint
0 2021/11/20 11:58:27
She needs an engine detail, been sitting for too long in my garage without any attention
She needs an engine detail, been sitting for too long in my garage without any attention
0 2021/11/20 11:58:11
0 2021/11/20 11:57:44
0 2021/11/20 11:56:55
0 2021/11/20 11:56:41
0 2021/11/20 11:56:22
0 2021/11/20 11:56:07
Final exhaust mockup. It's two mini bullet mufflers then dumps out of two Vibrant ultra quiet resonators. All piping is 3" 304SS. Drove it down the street and it sounds great. Didn't take it above 3k rpm so i don't know if it's raspy yet. I hope it isn't.
Final exhaust mockup. It's two mini bullet mufflers then dumps out of two Vibrant ultra quiet resonators. All piping is 3" 304SS. Drove it down the street and it sounds great. Didn't take it above 3k rpm so i don't know if it's raspy yet. I hope it isn't.
0 2019/04/04 16:44:38
0 2019/03/15 17:58:11
0 2019/02/24 15:14:03
Wrapping the headers is much easier when they are out of the car
Wrapping the headers is much easier when they are out of the car
0 2018/07/27 12:31:08
Ready to be shipped out for a stage 2 rebuild
Ready to be shipped out for a stage 2 rebuild
0 2018/07/27 12:29:16
1 step forward and 2 steps back. Engine and transmission back out.
1 step forward and 2 steps back. Engine and transmission back out.
0 2018/07/27 12:28:27
0 2018/06/16 15:21:10
Alignment is all out of whack and I still need to roll the rear fenders
Alignment is all out of whack and I still need to roll the rear fenders
0 2018/06/16 15:20:54
Finally got the drive it! Only about 10 feet but it was awesome.
Finally got the drive it! Only about 10 feet but it was awesome.
0 2018/06/16 15:20:36
Cut the top off of a 240sx pedal and welded it onto the stock G pedal. Works great with the Z32 throttle cable.
Cut the top off of a 240sx pedal and welded it onto the stock G pedal. Works great with the Z32 throttle cable.
0 2018/06/16 15:19:11
What was left of the license plate light bracket. Grabbed a new one and got it installed with LED bulbs
What was left of the license plate light bracket. Grabbed a new one and got it installed with LED bulbs
0 2018/06/12 13:51:42
Vroom Vroom
Vroom Vroom
0 2018/06/12 13:51:30
The WEDS look killer in the sunlight
The WEDS look killer in the sunlight
0 2018/06/12 13:51:11
Got a set of black housing eBay lights. They are just temporary. Gonna retrofit them to projectors once the car is driveable
Got a set of black housing eBay lights. They are just temporary. Gonna retrofit them to projectors once the car is driveable
0 2018/06/12 13:50:52
Didn't like the factory terminals so I installed these mil-spec ones and a distribution block for the positive terminal
Didn't like the factory terminals so I installed these mil-spec ones and a distribution block for the positive terminal
0 2018/06/12 13:32:28
Decided to start wrapping the headers once they were already installed 🤦
Decided to start wrapping the headers once they were already installed 🤦
0 2018/06/12 13:32:19
Couldn't find a pretty place to run the heater hoses.
Couldn't find a pretty place to run the heater hoses.
0 2018/06/12 13:32:12
Got the summer tires mounted. 265/40/18 on 18x9.5 +38 out back and 235/45/18 on 18x8.5 +35 up front
Got the summer tires mounted. 265/40/18 on 18x9.5 +38 out back and 235/45/18 on 18x8.5 +35 up front
0 2018/06/12 13:32:03
0 2018/05/02 17:48:26
Passenger side rear - tomorrow's project
Passenger side rear - tomorrow's project
0 2018/04/01 14:33:33
New PowerStop rotors, pads, and SS lines
New PowerStop rotors, pads, and SS lines
0 2018/04/01 14:32:40
Forgot to put the backing plate on, the rear shoes wouldn't have worked without it
Forgot to put the backing plate on, the rear shoes wouldn't have worked without it
0 2018/04/01 14:31:39
Got the driver's rear put back together - Energy Suspension bushings everywhere, Kinetic camber and toe arms, BC coils w/ Swift springs, Moog bearings and new hubs. That nasty caliper will be replaced as well.
Got the driver's rear put back together - Energy Suspension bushings everywhere, Kinetic camber and toe arms, BC coils w/ Swift springs, Moog bearings and new hubs. That nasty caliper will be replaced as well.
0 2018/03/31 15:14:03
Been about a year in the making so far. Soon....
Been about a year in the making so far. Soon....
0 2018/03/30 14:48:53
Test fitting new crank pulley and figuring out the proper belt size
Test fitting new crank pulley and figuring out the proper belt size
0 2018/03/30 14:47:52
Driveshaft on
Driveshaft on
0 2018/03/30 14:47:09
All bolted back into place
All bolted back into place
0 2018/03/30 14:46:22
All clean and covered in anti-sieze
All clean and covered in anti-sieze
0 2018/03/29 15:03:18
Cleaning up the terrible rusty threads so I have no issues lifting the subframe back into place
Cleaning up the terrible rusty threads so I have no issues lifting the subframe back into place
0 2018/03/29 15:01:23
Going to assemble the 10%UD pulley and try to get it bolted on tonight
Going to assemble the 10%UD pulley and try to get it bolted on tonight
0 2018/03/28 11:58:02