G35Driver - Infiniti G35 & G37 Forum Discussion
The plastic around the fuel indicator arm also had to be trimmed
The plastic around the fuel indicator arm also had to be trimmed
0 2017/05/28 18:55:30
Start with a small pilot hole and then use a step bit to get it to the right size
Start with a small pilot hole and then use a step bit to get it to the right size
0 2017/05/28 18:55:23
I used some cutting pliers and a Dremel to slowly flatten out a spot
I used some cutting pliers and a Dremel to slowly flatten out a spot
0 2017/05/28 18:55:16
The top of the fuel pump housing needs a spot cleared to accept the return fitting
The top of the fuel pump housing needs a spot cleared to accept the return fitting
0 2017/05/28 18:55:09
Soldered the new wire connection on
Soldered the new wire connection on
0 2017/05/28 18:55:02
0 2017/05/28 18:54:56
The plastic had to be notched a little bit to fit around the top of the pump
The plastic had to be notched a little bit to fit around the top of the pump
0 2017/05/28 18:54:49
New pump fit right in with the factory rubber isolator
New pump fit right in with the factory rubber isolator
0 2017/05/28 18:54:41
CJM blockoff in
CJM blockoff in
0 2017/05/28 18:54:34
OEM regulator thing out
OEM regulator thing out
0 2017/05/28 18:54:26
CJM return setup so I can install an aftermarket FPR
CJM return setup so I can install an aftermarket FPR
0 2017/05/28 18:51:18
Aeromotive 340lph fuel pump
Aeromotive 340lph fuel pump
0 2017/05/28 18:51:09
I wanted some extra peace of mind so I am using all four.
I wanted some extra peace of mind so I am using all four.
0 2017/05/28 18:43:27
Aftermarket front and rear steam vent lines
Aftermarket front and rear steam vent lines
0 2017/05/28 18:43:20
I think LS engines from '01 only have the front tubes installed from the factory.
I think LS engines from '01 only have the front tubes installed from the factory.
0 2017/05/28 18:43:12
Lubed them up and they slid right in
Lubed them up and they slid right in
0 2017/05/28 18:40:33
New poly bushings ready to go in
New poly bushings ready to go in
0 2017/05/28 18:40:25
Rack bushings pressed out
Rack bushings pressed out
0 2017/05/28 18:39:51
0 2017/05/28 18:39:42
0 2017/05/28 18:38:26
For what this thing cost, it's going to pay for itself real quick
For what this thing cost, it's going to pay for itself real quick
0 2017/05/28 18:38:18
Steering shaft U-joint, rack and pinion bushings, bearing & race driver set (for the chassis bushings), and CJM fuel return parts
Steering shaft U-joint, rack and pinion bushings, bearing & race driver set (for the chassis bushings), and CJM fuel return parts
0 2017/05/21 15:05:12
Outer tie rod ends, cabin air filter, parking brake shoes and hardware, wiper blades, and new front side markers
Outer tie rod ends, cabin air filter, parking brake shoes and hardware, wiper blades, and new front side markers
0 2017/05/21 15:03:31
WS harness and grounding kit
WS harness and grounding kit
0 2017/05/21 15:01:46
SIKKY oil pan looks and fits great
SIKKY oil pan looks and fits great
0 2017/05/21 14:59:47
New rack and pinion patiently waiting
New rack and pinion patiently waiting
0 2017/05/18 18:15:58
Old rack and pinion ready to be shipped back for a core
Old rack and pinion ready to be shipped back for a core
0 2017/05/18 18:15:50
Lots of work still to go
Lots of work still to go
0 2017/05/18 18:15:30
S13 gas pedal bolts right up
S13 gas pedal bolts right up
0 2017/05/18 18:13:32
0 2017/05/18 18:12:09
One side of the front almost completely apart
One side of the front almost completely apart
0 2017/05/18 18:09:15
Nice corrosion forming in the knuckle around where the bearing sat
Nice corrosion forming in the knuckle around where the bearing sat
0 2017/05/18 18:08:29
0 2017/05/18 18:08:20
0 2017/05/18 18:07:52
New bearings and hubs will be installed
New bearings and hubs will be installed
0 2017/05/18 18:05:29
OEM clutch master cylinder and lines getting replaced with a Wilwood unit
OEM clutch master cylinder and lines getting replaced with a Wilwood unit
0 2017/05/18 18:05:14
The lower steering shaft U-joint is getting replaced
The lower steering shaft U-joint is getting replaced
0 2017/05/18 18:05:04
The rear rotors practically fell apart after needing a hammer to get them off
The rear rotors practically fell apart after needing a hammer to get them off
0 2017/05/18 18:04:50
Knock sensors installed
Knock sensors installed
0 2017/05/18 18:00:50
LS6 Valley Cover
LS6 Valley Cover
0 2017/05/18 18:00:41