Forced Induction Discussion of turbos , superchargers , and nitrous upgrades on the G35

HKS supercharger and mechanical fan clearance

Thread Tools
 
Search this Thread
 
Rate Thread
 
  #1  
Old 03-15-2009 | 03:23 AM
GGGGGGGG's Avatar
Thread Starter
|
Registered User
iTrader: (1)
Joined: Sep 2003
Posts: 361
Likes: 0
HKS supercharger and mechanical fan clearance

Hi all,
Purchased a stage one HKS supercharger for my 04 sedan from Sam at GTM today and will be installed in two weeks. My concern is that if I will have a clearance issue since my car has a mechanical fan. Sam looked at the car this morning and felt that I should not have clearance issue when they do the install. However, I'd like to some opinons from the forum members if the clutch fan will be in the way of the supercharger. I've browsed several pictures of Gs and Zs with the supercharger and it seemed like a tight fit, and all of them, I think, have electric fans, instead of the belt-driven fan on my sedan. Should I be concerned about the fan clearance? Your advice is greatly appreciated. Thank you.
 
  #3  
Old 03-15-2009 | 05:18 AM
GGGGGGGG's Avatar
Thread Starter
|
Registered User
iTrader: (1)
Joined: Sep 2003
Posts: 361
Likes: 0
thank you for the assurance
 
  #4  
Old 04-15-2009 | 09:55 AM
MAZyar's Avatar
Registered User
Joined: Feb 2005
Posts: 205
Likes: 0
From: In your closet
any followup? how's you car on that hks? any dyno results??
 
  #5  
Old 04-23-2009 | 12:04 AM
GGGGGGGG's Avatar
Thread Starter
|
Registered User
iTrader: (1)
Joined: Sep 2003
Posts: 361
Likes: 0
Just a small update. The intall is completed a few days ago. As for the mechnical fan clearance, I had to get a new radiator (56mm PWR) and a new set of fans (GTM fan kit). Besides, the HKS kit fits like coupe and uses the same mounting points as coupe. For 2004.5 sedan and upwards with the electric fans, the kit will fit without mods. Now my car has been sitting at GTM for a little more than a month and counting, waiting for the Aquamist HFS-6 to arrive. As soon as the kit arrives, Sam will put it on the car, tune it, and dyno it. Hopefully, in the very, very, very near future.
 

Last edited by GGGGGGGG; 04-23-2009 at 12:08 AM.
  #6  
Old 04-24-2009 | 02:28 AM
str8dum1's Avatar
Registered User
iTrader: (1)
Joined: Feb 2006
Posts: 1,241
Likes: 5
From: raleigh-wood NC
meth kit on the stock block is kinda pointless. you are limited by the strength of the rods. something that adding meth cannot change.

i'd skip on that and just get it tuned and running.
 
  #7  
Old 04-24-2009 | 04:57 AM
GGGGGGGG's Avatar
Thread Starter
|
Registered User
iTrader: (1)
Joined: Sep 2003
Posts: 361
Likes: 0
I don't need to add more power, my main concern is reliability. To lower the internal temperature of the engine since I have the stock block. Also, I'll be tuned with only water, no meth for me. Just hate to give up on the kit after waiting for a whole month. I just can't let it go after all the time invested in waiting for this kit. what do you guys think? I have the stage IV kit btw if that makes a difference.
 
  #8  
Old 04-24-2009 | 05:00 AM
G37Rider92649's Avatar
Registered User
iTrader: (38)
Joined: Dec 2006
Posts: 5,605
Likes: 37
From: SoCal...OC..714..
HKS Supercharger eh??? Nice choice I loved mine while I had it, gtm custom fans and pwr radiator? Yup went that route too and cooling was never ever ever ever a issue again hahahaha. As for water/meth, I say go for it, it only does positive things, and if you decide to build your motor in the future then you don't have to buy it then. Good luck and have fun!! Post results when you done, smart choice on system and shop also.
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
KruZZe
New Members Check In
14
02-27-2023 06:04 PM
THMotorsports
Suspension-Vendor
257
12-18-2018 06:43 PM
RemmyZero
V36 DIY
10
04-23-2018 12:13 PM
g.spot
G35 Cars
12
05-09-2016 11:54 PM
9tray turbo
Media Share G35 Coupe V35
4
09-29-2015 11:22 PM



You have already rated this thread Rating: Thread Rating: 0 votes,  average.


All times are GMT -4. The time now is 10:26 PM.