3M Clear Bra?
#31
Originally Posted by G35_RJ
No refund, only an offer to redo the work. The catch: he wants me to drive my car 50 miles to his house and leave it overnight.
HeLL NO.
I filed a complaint with anyone who would listen... 3M, XPel, BBB, California Automotive, etc . For $700, I am also filing against him.
What crap... looks fine from far away. come close and your like wtf happened
http://www.kodakgallery.com/ShareLan...fromshare&Ux=0
On a better note, I spoke with Sam at Premier. Pretty cool guy and lots of great info. I'll be heading over there on the 21st...
HeLL NO.
I filed a complaint with anyone who would listen... 3M, XPel, BBB, California Automotive, etc . For $700, I am also filing against him.
What crap... looks fine from far away. come close and your like wtf happened
http://www.kodakgallery.com/ShareLan...fromshare&Ux=0
On a better note, I spoke with Sam at Premier. Pretty cool guy and lots of great info. I'll be heading over there on the 21st...
Hope it goes well getting your money back, and with your new install. All things pass...
#32
That really sucks. Sounds like he is as bad as my detailer says he is. Hope you get your money back somehow.
Originally Posted by G35_RJ
No refund, only an offer to redo the work. The catch: he wants me to drive my car 50 miles to his house and leave it overnight.
HeLL NO.
I filed a complaint with anyone who would listen... 3M, XPel, BBB, California Automotive, etc . For $700, I am also filing against him.
What crap... looks fine from far away. come close and your like wtf happened
http://www.kodakgallery.com/ShareLan...fromshare&Ux=0
On a better note, I spoke with Sam at Premier. Pretty cool guy and lots of great info. I'll be heading over there on the 21st...
HeLL NO.
I filed a complaint with anyone who would listen... 3M, XPel, BBB, California Automotive, etc . For $700, I am also filing against him.
What crap... looks fine from far away. come close and your like wtf happened
http://www.kodakgallery.com/ShareLan...fromshare&Ux=0
On a better note, I spoke with Sam at Premier. Pretty cool guy and lots of great info. I'll be heading over there on the 21st...
#36
Took my G to PMG today, the guys went above and beyond. Helped me remove the old crap, document it and buff out what they could. Man.. I should have use these guys from the get go. My bumper piece has razor markings all over the place. Profinish.. what a jack @ss loser. He should have known to just stop or run off sooner.
I've started the painful process of filing as much as I can against him and his POS mobile service.
USE PMG and don't cut cost when it comes to your baby!!! End of story...
I've started the painful process of filing as much as I can against him and his POS mobile service.
USE PMG and don't cut cost when it comes to your baby!!! End of story...
#37
#39
I took the car early this week to the dealer for 3M clear bra installed on my G. Went to the dealer today to pick up the car, WTF.. the dealer hired a 3M installer but the work was terrible. I can see some of my front bumper unprotected. All the 3M films were not stretch to all the corners. The installer just put the pre-cut pieces on the car. Once done, there were big gaps between corners and the films. Also, they only installed a small piece on the rear bumper. Damn, I didn't pay $800 to get a small rear bumper installed.
I told them to redo all again.
Does anyone have a closer picture of their car done with 3M (front & back)?
I told them to redo all again.
Does anyone have a closer picture of their car done with 3M (front & back)?
Last edited by 2K6G35; 12-06-2006 at 11:36 PM.
#42
Originally Posted by G35_RJ
I have plenty of images... Go to Premier, don't even waste time having morons do it...
Also, does Premier installation using one piece of film for each the front & rear bumper or a pre-cut films?
Let's see how they're going to redo them. If I am still not happy with the results, I will definitely go to Premier.
#43
premier used venture shield on mine.... bumper was single piece pre-cut..... headlights were pre-cut... and sideview mirrors were pre-cut as was the fender pieces..... hood piece was cut to form on the hood with the edges wrapped.... trailing edge lines up with fender pieces too.... one of the best $650 bucks i've spent.....just gotta clean and wax the the film occasionally to keep it smooth and clear... if you want pics, just pm me and i'll see if i can get some pics...
#44
Updated 12/9/06 - Finally they did redo the 3M clear bra on my car with a larger films than the 1st one. They also retouch the dings before reattaching the films. This time the clear bra looked better than before. It covered all the areas well. Although there were bubbles on some spots. Let's see in a few days.
Last edited by 2K6G35; 12-09-2006 at 10:35 PM.