Calling all sedans-What's your fender height?
iirc, ^ that pic was from before the alignment and I had adjusted the coils to an even 24" on all corners. I recently installed a rear camber kit, got different size tires and got my alignment done so the height in the rear changed quite a bit so I readjusted the height back to what I thought was 24".
I just went out and took the tape measure photos. Apparently my rears are uneven again, 24" and 24-1/8"
. The front are technically now 24-1/16" almost an 1/8";http://carphotos3.cardomain.com/imag...5854_large.jpg
http://carphotos4.cardomain.com/imag...5855_large.jpg
This is how she sits now though. Removed the front mudguards when I lowered it some more;
Can how much gas you have in your tank give you a gangster lean or did I forget to check the fenders after I adjusted the last time?
Registered User
Joined: Oct 2013
Posts: 48
Likes: 0
iirc, ^ that pic was from before the alignment and I had adjusted the coils to an even 24" on all corners. I recently installed a rear camber kit, got different size tires and got my alignment done so the height in the rear changed quite a bit so I readjusted the height back to what I thought was 24".
I just went out and took the tape measure photos. Apparently my rears are uneven again, 24" and 24-1/8"
. The front are technically now 24-1/16" almost an 1/8";http://carphotos3.cardomain.com/imag...5854_large.jpg
http://carphotos4.cardomain.com/imag...5855_large.jpg
This is how she sits now though. Removed the front mudguards when I lowered it some more;
Can how much gas you have in your tank give you a gangster lean or did I forget to check the fenders after I adjusted the last time?
Registered User
Joined: Apr 2012
Posts: 86
Likes: 8
From: Austin TX
25 1/2 front
25 3/4 rear
F&F coils
19" MRR wheels, 245 40 F and 275 35 rear
SPC Camber Rear
5mm spacers and Whiteline LCA and Compression rod bushings next on the list.
25 3/4 rear
F&F coils
19" MRR wheels, 245 40 F and 275 35 rear
SPC Camber Rear
5mm spacers and Whiteline LCA and Compression rod bushings next on the list.
Last edited by DRVNFAST; Mar 26, 2014 at 11:29 AM.
Registered User
Joined: May 2011
Posts: 2
Likes: 0
I just got those bc racing BR for AWD infiniti
I love how you car looks and i was wonde if i could know you drop set up. I drope mine to much. I live in ny toad here are not that great. But i like how u car looks its nice
Registered User
Joined: Apr 2012
Posts: 86
Likes: 8
From: Austin TX
You are just going to have to play with them. I started low and have worked my way to this ride height after about 5 or so adjustments.
Good Luck
Registered User
Joined: May 2011
Posts: 2
Likes: 0
Like Blue Dream confirmed, I have Function and Form Coils which allow for a crazy low drop. I have mine about an inch off the bottom of the rear cups (meaning I'm barely dropped) with these coils. If I wanted this thing to sit on the ground these coils would allow it. however this is my DD so that is less than ideal.
You are just going to have to play with them. I started low and have worked my way to this ride height after about 5 or so adjustments.
Good Luck
You are just going to have to play with them. I started low and have worked my way to this ride height after about 5 or so adjustments.
Good Luck
Thank you for the info. I do have coil too. I just got the bc racing br type installed on my g35. I wanted the koni. But they dont made those for AWD. But i am loving this bc now
however i had to hight up my car because it was to low i wasent able to drive without hitting my car with the gronw lol
Thread
Thread Starter
Forum
Replies
Last Post
THMotorsports
Suspension-Vendor
257
Dec 18, 2018 05:43 PM
RemmyZero
V36 DIY
10
Apr 23, 2018 11:13 AM
FS[NorEast]: New OEM G35x Compression Rods - Save!!
The Fixer
Steering & Suspension
15
Nov 1, 2015 03:26 PM
