New G35 owner, limp mode help - Page 2 - G35Driver - Infiniti G35 & G37 Forum Discussion
Show Your Support Become A Premier Member



G35 Sedan V35 2003-06 Discussion about the 1st Generation V35 G35 Sedan

New G35 owner, limp mode help

Reply
 
 
 
Thread Tools Search this Thread Rate Thread
  #16  
Old 09-16-2011, 07:59 PM
Registered User
Thread Starter
 
Join Date: Sep 2011
Location: Alberta, Canada
Posts: 26
Thanks: 0
Thanked 1 Time in 1 Post
Thanks for the helpful advice DaveB, I'm gonna do some more research into the things you suggested I look into and if it's not difficult I'll do the testing myself. Thanks again and I'll keep you guys posted. They have my car until Monday again.
Reply With Quote
  #17  
Old 09-21-2011, 08:47 PM
Registered User
Thread Starter
 
Join Date: Sep 2011
Location: Alberta, Canada
Posts: 26
Thanks: 0
Thanked 1 Time in 1 Post
So here's an update, we finally resolved the issue I'm hoping. Been driving it all day and no issues. So it's a Canadian car and has a black DRL module in the engine bay. The tech said it takes a wire from the alternator and relays it to the instrument cluster in the car. We noticed my DRL's weren't running so they traced it back to that module and it was water soaked, corroded and moldy. The tech suspected that it was grounding out and not sending the signal to the cluster and resulting in low voltage all around the car. I'm hoping this is the final time it's in the shop. I'd like to thank everyone who gave me advice and offered their help.
Reply With Quote
  #18  
Old 08-23-2014, 10:24 PM
Registered User
 
Join Date: Aug 2014
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
hello man what's up I was wondering if you ever found your problem I have a similar problem as yours I have a 2004 infiniti g35 coupe and my problem starts from no where it was just a really hot day I was driving my car and them it loose power my slip vcd and check engine turn on the accelerator was responding to slow and I replace the throttle body the pedal position sensor and still the same I also notice that my tire pressure light are on but I just to have a 350z with tire pressure light on and never give me problems anyway I remove all the grounds I found and after moving a lot of staffs I found that the main ground that connects to the engine right under the water hose on the passenger side was corroded so I clean it and I put everything back together and banggg it was working fine and everything so I start putting everything back on the car cuz it was completely disarm and I disconnect that cable again and some other grounds to put this funny cream anti corrosion and when I turn the car back on those annoying lights vcd slip and check engine codes are p2128 p2127 p2138 and what I notice is that if I'm holding the pedal brake the car runs just fine I can rev it up and everything appears to work fine so I assume it was related to the brake switches I replace them and still the same so I try disconnecting the brake sensor on the bottom and it works fine no vcd slip check engine light but if I put the car on drive and push the accelerator hard it goes into limp mode again WTH so I'm assuming this thing is related with this sensor or the module that controls it I don't know much of electronic things but if I plug the multimeter on the accelerator pedal with the brake pedal depress I'm getting 5.0 volts I believe but if I release the brake with the car on or ignition switch on it raise to 12. something volts and if the car is on it goes to like 13 or 14 volts and I think it supposed to stays at 5. something volts if I'm right so im getting a really hard time with this car any help would be appreciated thanks
Reply With Quote
  #19  
Old 05-15-2018, 04:17 PM
Registered User
 
Join Date: May 2018
Posts: 9
Thanked 0 Times in 0 Posts
Quote:
Originally Posted by DARLLL View Post
I had this same problem 6 months ago whereby the car would not go past 10-20mph even when the pedal was floored......I drove it in limp mode to my local mechanic who was 15miles away and the minute i got there he took out the sensor that is connected to the air filter. He then purchased a spray from autozone and cleaned the sensor..

The whole procedure took about 10mins and by the time he put back the sensor, my car was back to its full potential..I really wish i knew the name of the sensor he took out but am not sure, although i know it was connected to the air filter in some way...

Hope this helps ....By the way i have an 03 g35 sedan

YOOOO thats the mass air flow i believe
Reply With Quote
  #20  
Old 05-15-2018, 04:42 PM
Blue Dream's Avatar
I drove ttrank's car solo
iTrader: (50)
 
Join Date: Mar 2009
Location: By the sea, Tx
Posts: 16,848
Thanked 1,268 Times in 1,030 Posts
Thanks for responding to a 7 year old thread lol.
Reply With Quote
The Following User Says Thank You to Blue Dream For This Useful Post:
[email protected] (05-15-2018)
  #21  
Old 05-15-2018, 04:49 PM
cleric670@gmail's Avatar
Cleric670
 
Join Date: May 2017
Location: Washington State
Posts: 3,460
Thanked 332 Times in 319 Posts
Quote:
Originally Posted by asianman123 View Post
YOOOO thats the mass air flow i believe
If you bothered to actually READ the thread you would know it was the canadian DRL module was saturated with water and screwing up the electronics of the vehicle causing a temporary limp mode condition.
Reply With Quote
  #22  
Old 05-16-2018, 07:30 AM
Registered User
 
Join Date: May 2018
Posts: 9
Thanked 0 Times in 0 Posts
Quote:
Originally Posted by Blue Dream View Post
Thanks for responding to a 7 year old thread lol.
how else am I going make friends
Reply With Quote
  #23  
Old 05-16-2018, 07:30 AM
Registered User
 
Join Date: May 2018
Posts: 9
Thanked 0 Times in 0 Posts
Quote:
Originally Posted by [email protected] View Post
If you bothered to actually READ the thread you would know it was the canadian DRL module was saturated with water and screwing up the electronics of the vehicle causing a temporary limp mode condition.
thanks mr mechanics man for correcting me
Reply With Quote
  #24  
Old 05-16-2018, 04:05 PM
Blue Dream's Avatar
I drove ttrank's car solo
iTrader: (50)
 
Join Date: Mar 2009
Location: By the sea, Tx
Posts: 16,848
Thanked 1,268 Times in 1,030 Posts
I think what he's trying to politely say is don't be a lazy azz and educate yourself on a topic before you look like a fool with a useless post.

Also please don't start multiple threads on a single topic. This clutters up the forum and is against forum rules. You don't want to rack up infractions just because you're immature and impatient. Thanks.....
Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
FS[Canada]: G35 OEM Style Lip Spoiler netcbc Exterior - Body Parts CDN 2 08-21-2015 09:50 AM
FS: G35 Quad Projectors VANST3R Lights 2 07-27-2015 08:20 PM
FS: G35 coupe front splash guards in black obsidian color laksjd84 Exterior - Body Parts 1 07-24-2015 05:12 PM
Manual mode in automatic Cskeet Engine, Drivetrain & Forced-Induction 3 07-21-2015 05:48 PM
Getting P1128 code - Throttle Control Motor Circuit Short Hasanbaloch Engine, Drivetrain & Forced-Induction 5 07-19-2015 02:13 PM


Tags
2000, 2000rpm, dealer, driver, forum, g35, g37, infiniti, limp, mode, past, power, pressure, rev, rpm, steering, switch, wont

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 06:05 AM.


Copyright ©2002 - 2017, G35DRIVER.COM All Rights Reserved.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
 
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in: