Nismo Front Bumper Install (comments/suggestions/how toos)
#46
Originally Posted by JOKER
UPDATE:
OK I take everything that I said about not fastening this piece of plastic to the bumper back. YOU GOT TO ATTACH IT.
Force of the air that goes under your car will actually push it out from behind the bumper due to that vertical piece that's hanging from the bumper at around 120mph. And it will scrape like a Motha Fvcka.
I came up with a few ways to attach it and I'm going to attempt it today.
I'll post update when I do it.
OK I take everything that I said about not fastening this piece of plastic to the bumper back. YOU GOT TO ATTACH IT.
Force of the air that goes under your car will actually push it out from behind the bumper due to that vertical piece that's hanging from the bumper at around 120mph. And it will scrape like a Motha Fvcka.
I came up with a few ways to attach it and I'm going to attempt it today.
I'll post update when I do it.
hey joker, if u take off the middle plastic piece will that be okay? Will the bumper bend more at hi speeds without the middle bottle piece and only having the plastic sides connected to the bumper.
#47
You have to take off the 90 degree angle. Because at hight speed wind resistance will rip out the plastic that it's attached to and it will scrape on the ground.
And mounting the sides of the bumper is not enough also
Same thing will happen even without the angle. So just drill holes through bumper and black plastic right in front of holes that angle piece attached to and use zip tie
Here how mine looks like
View from the top. (between the grille and the engine)
View from the bottom
View of a zip tie
As you can see I drilled holes in front of nuts where bolts that held 90 degree angle piece went in.
You need two ppl for that. One need to be drilling under the car and another needs to be holding/pushing on the bumper from the top. For this you need to take the grille out for better access.
Then just put a zip tie through both holes and you are done.
Fastest I went with that set up is 130 mph and nothing happened.
I could not go 75 mph before it was not attached and 90 degree angle removed. It would just fly out and start scraping.
And mounting the sides of the bumper is not enough also
Same thing will happen even without the angle. So just drill holes through bumper and black plastic right in front of holes that angle piece attached to and use zip tie
Here how mine looks like
View from the top. (between the grille and the engine)
View from the bottom
View of a zip tie
As you can see I drilled holes in front of nuts where bolts that held 90 degree angle piece went in.
You need two ppl for that. One need to be drilling under the car and another needs to be holding/pushing on the bumper from the top. For this you need to take the grille out for better access.
Then just put a zip tie through both holes and you are done.
Fastest I went with that set up is 130 mph and nothing happened.
I could not go 75 mph before it was not attached and 90 degree angle removed. It would just fly out and start scraping.
Last edited by JOKER; 10-14-2008 at 06:58 PM.
#48
thanks for the pix... going to try to attempt to install mine today.
U know, I was quoted 650 out the door for painting the front nismo (removing tow hook) and also stripping and blending the side fenders (around the head lights) and hood (lower portion) due to major rock chips. Is that too cheap?
U know, I was quoted 650 out the door for painting the front nismo (removing tow hook) and also stripping and blending the side fenders (around the head lights) and hood (lower portion) due to major rock chips. Is that too cheap?
#49
Originally Posted by Mr_pharmD
thanks for the pix... going to try to attempt to install mine today.
U know, I was quoted 650 out the door for painting the front nismo (removing tow hook) and also stripping and blending the side fenders (around the head lights) and hood (lower portion) due to major rock chips. Is that too cheap?
U know, I was quoted 650 out the door for painting the front nismo (removing tow hook) and also stripping and blending the side fenders (around the head lights) and hood (lower portion) due to major rock chips. Is that too cheap?
#50
Originally Posted by Mr_pharmD
thanks for the pix... going to try to attempt to install mine today.
U know, I was quoted 650 out the door for painting the front nismo (removing tow hook) and also stripping and blending the side fenders (around the head lights) and hood (lower portion) due to major rock chips. Is that too cheap?
U know, I was quoted 650 out the door for painting the front nismo (removing tow hook) and also stripping and blending the side fenders (around the head lights) and hood (lower portion) due to major rock chips. Is that too cheap?
I'm not getting this part.
I think it's not that bad as long as they do a good job.
You can prolly find it cheaper somewhere.
#51
#53
yeah i mounted all my holes back into the factory spots....or at least all my holes were mounted back on my ARC underbody panel...The one issue was that there were no holes drilled into the mounting spots in the bumper so i mounted it onto the car and drilled holes into where it had to go...i even used the OEM metal clips for the OEM screws to be mounted back in.
#54
#59