White turn signal bulbs + fog lights

Old Sep 9, 2009 | 01:47 AM
  #1  
Mike_10PL's Avatar
Thread Starter
|
Registered User
iTrader: (4)
Joined: Feb 2007
Posts: 135
Likes: 0
White turn signal bulbs + fog lights

Hey guys.. do you have some recommendation for turn lights G35 '06? I bought some leds from VLED but after installation my turn signal lights are flashing way too fast like they are burned out :/
PS. What fog lights (White/blue) would you recommend?
Thx
 
Reply
Old Sep 9, 2009 | 07:35 AM
  #2  
slvrg05's Avatar
Registered User
iTrader: (18)
Joined: Aug 2007
Posts: 787
Likes: 2
From: tampa
do you want HID's in them ?
 
Reply
Old Sep 9, 2009 | 05:30 PM
  #3  
Mike_10PL's Avatar
Thread Starter
|
Registered User
iTrader: (4)
Joined: Feb 2007
Posts: 135
Likes: 0
yup but I really would need some white/blue turn signal bulbs which would work for sure.. someone told me that in current ones voltage is too low and that's why they are flashing too fast :/
 
Reply
Old Sep 19, 2009 | 10:44 AM
  #4  
caddyshack's Avatar
Registered User
Joined: Dec 2008
Posts: 10
Likes: 0
From: Brewster NY
For the turn signals you will need to get a set of the load resistors that they sell on vled. The resistors will up the overall current draw of the system to that of one with factory incandescent bulbs. That should take care of the hyper-blinking issue.
 
Reply
Old Sep 30, 2009 | 08:07 PM
  #5  
Mike_10PL's Avatar
Thread Starter
|
Registered User
iTrader: (4)
Joined: Feb 2007
Posts: 135
Likes: 0
Originally Posted by caddyshack
For the turn signals you will need to get a set of the load resistors that they sell on vled. The resistors will up the overall current draw of the system to that of one with factory incandescent bulbs. That should take care of the hyper-blinking issue.

OK so I just bought those resistors.. installed them.. and got another issue lol
When I start the car my turn signals will flash once and then.. nothing. Like it's off or dead.. then when I switch it to off position and then turn it again same thing.. flashes once and then dead.. after 10 minutes of driving it works fine..
Any ideas?
I think that the problem may be that I bought bigger resistors for 4 LEDs so I should have LEDs in rear too but there's a stock bulb..
 
Reply
Old Sep 30, 2009 | 10:39 PM
  #6  
caddyshack's Avatar
Registered User
Joined: Dec 2008
Posts: 10
Likes: 0
From: Brewster NY
Originally Posted by Mike_10PL
OK so I just bought those resistors.. installed them.. and got another issue lol
When I start the car my turn signals will flash once and then.. nothing. Like it's off or dead.. then when I switch it to off position and then turn it again same thing.. flashes once and then dead.. after 10 minutes of driving it works fine..
Any ideas?
I think that the problem may be that I bought bigger resistors for 4 LEDs so I should have LEDs in rear too but there's a stock bulb..
Maybe, it might be seeing too much of a load? When you say it starts working after 10 minutes, is that based on the interior indicator blinking or by the led and rear bulb blinking?

Also, one thing to try with the larger resistors would be to pull the rear bulb. If the larger resistor really is the issue than the overall load should be correct with this bulb out...just a guess though... That or replace one of the rear bulbs with one of the LEDs from the front and see if that single side works...

Good Luck, post back what you find!
 
Reply
Old Sep 30, 2009 | 10:58 PM
  #7  
Mike_10PL's Avatar
Thread Starter
|
Registered User
iTrader: (4)
Joined: Feb 2007
Posts: 135
Likes: 0
Originally Posted by caddyshack
Maybe, it might be seeing too much of a load? When you say it starts working after 10 minutes, is that based on the interior indicator blinking or by the led and rear bulb blinking?

Also, one thing to try with the larger resistors would be to pull the rear bulb. If the larger resistor really is the issue than the overall load should be correct with this bulb out...just a guess though... That or replace one of the rear bulbs with one of the LEDs from the front and see if that single side works...

Good Luck, post back what you find!

It's based on both interior indicator blinking and both bulbs.
I was thinking about 2 options.. get 2 new resistors (smaller ones) or replace the bulbs in rear for LED... but you know how complicated it is to take the rear bulb out and I installed resistors really deep so I need to take my wheels off so I decided ask here first
Thanx!
 
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Muski_G
G35 Coupe V35 2003 - 07
18
Dec 1, 2023 11:11 AM
Jusseth
G35 Sedan V35 2003-06
16
Sep 13, 2020 12:25 PM
Freddy07g35
The G-Spot
22
Sep 17, 2015 08:53 PM
MT6002
Lighting
0
Jul 21, 2015 01:13 PM
attarday
General Tech Questions
7
Jul 15, 2015 04:03 PM


Thread Tools
Search this Thread
Rate This Thread
Rate This Thread:
You have already rated this thread Rating: Thread Rating: 0 votes,  average.


All times are GMT -4. The time now is 04:05 PM.