Nissan Power Pup Bullydog - First Impressions
#631
#633
You will start to notice it after a while, you should also see a gas mileage increase as well. ECU has to sort of get used to the tune.
#635
#636
Question about returning back to stock
Hi. I'm trying to return the ECU back to stock. Bully dog has been running for nearly 45 minutes now... and its been stuck on 0% @ the downloading screen.
Anyone else have this ? or am I just not patient enough?
Installing didnt take this long...
UPDATE: after about 1.5hrs stuck on 0% i unplugged it from the car. started the car to check if everything was ok and turned off the engine. plugged BD PP back in and it seems everything is running fine and the tune is still there. Guess i'll try again tomorrow.
Anyone else have this ? or am I just not patient enough?
Installing didnt take this long...
UPDATE: after about 1.5hrs stuck on 0% i unplugged it from the car. started the car to check if everything was ok and turned off the engine. plugged BD PP back in and it seems everything is running fine and the tune is still there. Guess i'll try again tomorrow.
Last edited by a6g35; 07-22-2009 at 10:33 PM. Reason: update
#637
Hi. I'm trying to return the ECU back to stock. Bully dog has been running for nearly 45 minutes now... and its been stuck on 0% @ the downloading screen.
Anyone else have this ? or am I just not patient enough?
Installing didnt take this long...
UPDATE: after about 1.5hrs stuck on 0% i unplugged it from the car. started the car to check if everything was ok and turned off the engine. plugged BD PP back in and it seems everything is running fine and the tune is still there. Guess i'll try again tomorrow.
Anyone else have this ? or am I just not patient enough?
Installing didnt take this long...
UPDATE: after about 1.5hrs stuck on 0% i unplugged it from the car. started the car to check if everything was ok and turned off the engine. plugged BD PP back in and it seems everything is running fine and the tune is still there. Guess i'll try again tomorrow.
That has happened to me before. just back it up to the factory tune and then reinstall the BD tune to make sure.
#639
The DL didn't go through. "stuck at 0%"
...probably doesn't have a good file yet.
I'm still in the holding pattern as well.
Talked to tech yesterday & they're still working on it.
I'm not too concerned though, I still want to arrange a base line pull before I install it.
.....just haven't had the time.
#640
I already did the premium tune and I was trying to return the car to stock last night. (Need to install paddle shifters). But it got stuck on 0% @ the download stage while trying to return to stock. According to PP, I still have all the tuned settings on my car in the "view settings" screen. However, the car is different today from yesterday.
Ex: My idle rpm at startup previous to this incident was above 2100rpm. But this morning, my idle rpm at startup was no more than 1800rpm. The throttle feels a little different too. not sure. I'm hoping PP didnt return my car to stock but still keep my engine code on the PP unit.
I'm going to try and "return to stock" again tonight.
Ex: My idle rpm at startup previous to this incident was above 2100rpm. But this morning, my idle rpm at startup was no more than 1800rpm. The throttle feels a little different too. not sure. I'm hoping PP didnt return my car to stock but still keep my engine code on the PP unit.
I'm going to try and "return to stock" again tonight.
#641
Keep us updated. Just an update on my vehicle...... no problems to report.... I put at least 30+ miles a day on my vehicle and haven't had any problems. Had my fluids checked and oil change changed. I'm still rocking out 1.22b (need to update eventually). I did take the +2 timing off because I'm trying to get a dyno run scheduled with my local shop. (Will do a +2 timing and a neutral timing).
#644
#645
Did you Bump the Timing? seems like that would have the most effect for performance. i gained 1-2 MPG