G35Driver - Infiniti G35 & G37 Forum Discussion
Dirty throttle body, old coolant sensor, and new thermostat.
Dirty throttle body, old coolant sensor, and new thermostat.
0 2018/10/05 21:57:32
0 2018/10/05 21:56:21
0 2018/09/23 16:04:11
This is most of the cancer that's left.
This is most of the cancer that's left.
0 2018/09/20 19:50:23
Inside the panel is 100% clean now
Inside the panel is 100% clean now
0 2018/09/20 19:46:25
Black is rust converter, green is Eastwood internal frame coating. All metal inside and out is completely 100% solid now.
Black is rust converter, green is Eastwood internal frame coating. All metal inside and out is completely 100% solid now.
0 2018/09/20 19:44:33
0 2018/09/20 19:44:24
0 2018/09/20 19:34:41
Sweet sweet success
Sweet sweet success
0 2018/09/20 17:23:40
Bottom nut installed with washer to distribute load on the K member. Should be stronger than stock.
Bottom nut installed with washer to distribute load on the K member. Should be stronger than stock.
0 2018/09/20 17:22:32
Dimensions of fabricated washers to distribute stress. Got the steel from Home Depot, used a sawzall, angle grinder, and drill to fabricate.
Dimensions of fabricated washers to distribute stress. Got the steel from Home Depot, used a sawzall, angle grinder, and drill to fabricate.
0 2018/09/20 17:19:18
JB weld and rust converter FTW
JB weld and rust converter FTW
0 2018/09/20 17:18:58
My K member after hammering out the broken piece.
My K member after hammering out the broken piece.
0 2018/09/20 17:18:15
0 2018/09/20 17:17:59
Pulling broken driver side mount out with top nut loosely attached. You could cut it out as well if you didn't want to drop the K member.
Pulling broken driver side mount out with top nut loosely attached. You could cut it out as well if you didn't want to drop the K member.
0 2018/09/20 17:16:14
This is a regular length wrench attached to the top rear passenger side bracket bolt. Good luck.
This is a regular length wrench attached to the top rear passenger side bracket bolt. Good luck.
0 2018/09/20 17:04:49
Breaking torque on driver side top nut
Breaking torque on driver side top nut
0 2018/09/20 17:00:04
0 2018/09/20 15:13:14
0 2018/08/27 12:17:02
0 2018/08/27 12:15:49
0 2018/08/17 20:14:42
0 2018/08/17 20:14:40
0 2018/08/10 23:21:38
I fabbed these guys up with an angle grinder, sawzall, and drill to fit in that entire slot to take the stress off the JB welded sections.
I fabbed these guys up with an angle grinder, sawzall, and drill to fit in that entire slot to take the stress off the JB welded sections.
0 2018/08/10 23:17:02
This side turned out pretty good.
This side turned out pretty good.
0 2018/08/10 23:16:42
Deja vu
Deja vu
0 2018/08/10 23:16:39
0 2018/08/10 11:04:52
Here's the contrast with the original finish. I was going to do the whole thing but I like the two-tone so maybe that's just an excuse to buy a lighter colored wrap!
Here's the contrast with the original finish. I was going to do the whole thing but I like the two-tone so maybe that's just an excuse to buy a lighter colored wrap!
0 2018/08/10 08:15:52
0 2018/08/09 22:07:39
0 2018/08/09 22:03:47
0 2018/08/09 22:03:30
Took off bottom mount nut and jacked up engine trying to get more room, this is what the better of the two mounts looks like...
Took off bottom mount nut and jacked up engine trying to get more room, this is what the better of the two mounts looks like...
0 2018/07/27 06:45:21
This is as far as I've gotten but because of that angle and an inability to get leverage the tool always slips off.
This is as far as I've gotten but because of that angle and an inability to get leverage the tool always slips off.
0 2018/07/27 06:45:06
There is is all the way at the bottom! Note the terribly designed wings on the motor bracket preventing access from any direction but directly facing the frame... Doh.
There is is all the way at the bottom! Note the terribly designed wings on the motor bracket preventing access from any direction but directly facing the frame... Doh.
0 2018/07/27 06:44:42
0 2018/06/27 07:00:45
0 2018/06/18 10:12:44
0 2018/06/13 07:43:34
0 2018/06/12 06:05:39
0 2018/06/12 06:05:34
0 2018/06/12 06:05:30