BC VS Stance Coilover
#31
05-20-2011, 11:29 AM
Registered User
Coils
Thanks for the feedback guy. I think i am heading in the direction of the Stance coils. Plus i know eventually i will want to slam it as far as it can go. just threw out a 1" number to see what people say. I have all the tools to put them on myself. I am just a little ifffy about the back setup and how to install it. Anyone have any threads explaining in detail about the back one.DOMO
#32
05-20-2011, 11:31 AM
Registered User
I too recommend just springs, like the eibach prokit... but I'll give you my opinion on coils anyways.
Ride wise, by the book the BCs will ride better due to the lower spring rates (8k and 10k) but stance coils ride amazing in my opinion.
I think BCs can be had for about $900 shipped inside of the states, Stance are about $1200 shipped inside the states.
You'll need to have them installed if you're not up to it which is usually $200-$300 labor charge.
All that being said.
Stance.
Says in the first page, BCs are made in Taiwan, stance are made in Japan. Do you want the Infiniti? or the Kia?
Ride wise, by the book the BCs will ride better due to the lower spring rates (8k and 10k) but stance coils ride amazing in my opinion.
I think BCs can be had for about $900 shipped inside of the states, Stance are about $1200 shipped inside the states.
You'll need to have them installed if you're not up to it which is usually $200-$300 labor charge.
All that being said.
Stance.
Says in the first page, BCs are made in Taiwan, stance are made in Japan. Do you want the Infiniti? or the Kia?
#33
05-21-2011, 12:00 AM
Join Date: Mar 2009
Location: By the sea, Tx
Posts: 18,299
Received 1,486 Likes
on
1,221 Posts
G35 sedan w/ too much money in mods
http://intensepower.com/strecaarni35.html
#34
06-22-2011, 11:51 PM
Stance coilovers are not made in Japan... I think they might be make in Korea but I know they're not made in Japan
Last edited by jumbaco; 06-22-2011 at 11:56 PM.
#35
06-23-2011, 01:48 PM
#36
06-23-2011, 04:39 PM
being made in Japan is different then being assembled in Japan. where are the dampers themselves(which I consider to be the most important part) made?
On a side note, these are the coilovers from my buddy's FC. He has Stance on them and he was pretty upset with them. They're way to close to the rear knuckles and he needed to add a washer to space it out some. IT ground the coilover down quite a bit
On a side note, these are the coilovers from my buddy's FC. He has Stance on them and he was pretty upset with them. They're way to close to the rear knuckles and he needed to add a washer to space it out some. IT ground the coilover down quite a bit
Last edited by jumbaco; 06-23-2011 at 04:47 PM.
#38
06-23-2011, 06:31 PM
being made in Japan is different then being assembled in Japan. where are the dampers themselves(which I consider to be the most important part) made?
On a side note, these are the coilovers from my buddy's FC. He has Stance on them and he was pretty upset with them. They're way to close to the rear knuckles and he needed to add a washer to space it out some. IT ground the coilover down quite a bit
On a side note, these are the coilovers from my buddy's FC. He has Stance on them and he was pretty upset with them. They're way to close to the rear knuckles and he needed to add a washer to space it out some. IT ground the coilover down quite a bit
Did you call stance BTW? ask them regarding their parts? Origin etc....
Thread
Thread Starter
Forum
Replies
Last Post
THMotorsports
Suspension-Vendor
257
12-18-2018 05:43 PM
VatoVazq
Steering & Suspension
15
12-23-2015 10:01 AM
