What did you do to the G today?
#5416
well its going to be pretty much the same as doing a dual ring install. its just this will be much cleaner. i mean you still gotta open up the tail light, and cut off the existing ring but that is pretty much it. the led pcb has holes so the bezel will snap in and then the bezel has holes so the diffuser lens just snaps in.
i know the lens is still not totally clear which bothers me, even though i polished this thing for a long *** time. i just bought a bunch of silicone and resin and am going to try to cast this 3d print in crystal clear resin to get a better result.and then i gotta send the bezel off to get chromed.
lol i wasnt really intending to mass produce these to sell. there was just a minimum order qty on custom pcbs so i tagged em with my name haha. i only have 4 extra sets. buying all the resistors and electrical pieces from digikey now.
edit: showing fitment on the last pic. i still have to trim the edge of the bezel just a bit for a totally flush fit. there isnt very much room on the side of the opening so its gotta come super close. havent gotten around to trimming yet bec i was waiting for these pcbs to come in and get the orientation right first
i know the lens is still not totally clear which bothers me, even though i polished this thing for a long *** time. i just bought a bunch of silicone and resin and am going to try to cast this 3d print in crystal clear resin to get a better result.and then i gotta send the bezel off to get chromed.
lol i wasnt really intending to mass produce these to sell. there was just a minimum order qty on custom pcbs so i tagged em with my name haha. i only have 4 extra sets. buying all the resistors and electrical pieces from digikey now.
edit: showing fitment on the last pic. i still have to trim the edge of the bezel just a bit for a totally flush fit. there isnt very much room on the side of the opening so its gotta come super close. havent gotten around to trimming yet bec i was waiting for these pcbs to come in and get the orientation right first
The following 4 users liked this post by .cakestar:
#5420
#5423
Having both I must warn you the trans mount will induce a Subaru exhaust sound and vibrations in your cabin. Lol
Last edited by JKL1031; 12-29-2015 at 06:43 PM.
#5427
Premier Member
iTrader: (11)
well its going to be pretty much the same as doing a dual ring install. its just this will be much cleaner. i mean you still gotta open up the tail light, and cut off the existing ring but that is pretty much it. the led pcb has holes so the bezel will snap in and then the bezel has holes so the diffuser lens just snaps in.
i know the lens is still not totally clear which bothers me, even though i polished this thing for a long *** time. i just bought a bunch of silicone and resin and am going to try to cast this 3d print in crystal clear resin to get a better result.and then i gotta send the bezel off to get chromed.
lol i wasnt really intending to mass produce these to sell. there was just a minimum order qty on custom pcbs so i tagged em with my name haha. i only have 4 extra sets. buying all the resistors and electrical pieces from digikey now.
edit: showing fitment on the last pic. i still have to trim the edge of the bezel just a bit for a totally flush fit. there isnt very much room on the side of the opening so its gotta come super close. havent gotten around to trimming yet bec i was waiting for these pcbs to come in and get the orientation right first
i know the lens is still not totally clear which bothers me, even though i polished this thing for a long *** time. i just bought a bunch of silicone and resin and am going to try to cast this 3d print in crystal clear resin to get a better result.and then i gotta send the bezel off to get chromed.
lol i wasnt really intending to mass produce these to sell. there was just a minimum order qty on custom pcbs so i tagged em with my name haha. i only have 4 extra sets. buying all the resistors and electrical pieces from digikey now.
edit: showing fitment on the last pic. i still have to trim the edge of the bezel just a bit for a totally flush fit. there isnt very much room on the side of the opening so its gotta come super close. havent gotten around to trimming yet bec i was waiting for these pcbs to come in and get the orientation right first
#5429
cleanest dual ring tail light setup? this one will replace the stock controller board, has an extra port for the extra ring so it will be plug n play. also has an extra port to integrate the turn signal wire and will have the second ring work as the turn signal. and also an extra port for an led drl for the light on the side. like the sedan
#5430