I'm planning to tackle the DIY fender roll in about 1 week. I'll be using a PBM roller and have a heat gun. Never done this before and I can't say I'm excited about my G being the guinea pig, but I live in the midwest, which means local shops have either never heard of rolling fenders or won't do it cuz of liability issues.
Anyway, just looking for tips to hopefully achieve a successful DIY roll, specifically what people do with the fender-liner up front. Do I need to unbolt that from the fender, or just leave it in place as I go?
Anyway, just looking for tips to hopefully achieve a successful DIY roll, specifically what people do with the fender-liner up front. Do I need to unbolt that from the fender, or just leave it in place as I go?
Registered User
gary c
Registered User
close
- Join DateFeb 2005
- LocationValencia, Ca
- Posts:19,433
-
iTrader Positive Feedback100
-
iTrader Feedback Score(10)
-
Likes:69
-
Liked:1,133 Times in 1,003 Posts
Old School...."Baseball Bat" but you need to go very slow. If you need fender roll up front I wouldn't DIY, unlike the rear openings the front fenders flex too much. Shame you don't live here, we have body shops that can even streatch our fenders 2 inches....
Gary

Gary
I don't think the phrase "baseball bat" should enter a tips thread on successful DIY fender rolling...
Registered User
NjMatteSedan
Registered User
close
- Join DateApr 2009
- LocationElmwood Park. NJ
- Posts:7,985
-
iTrader Positive Feedback100
-
iTrader Feedback Score(3)
-
Likes:277
-
Liked:98 Times in 82 Posts
cut them
Registered User
look on youtube they have alot of clips on fender rolling,and don't use a baseball bat.I'd spent the extra money on a fender roller tool just to do it right..but you do have a fender roller tool already so good start.also look on eastwood on their fender roller tool I think they have a short video on rolling a fender..but most important take your time...
Registered User
I've read, and it makes sense, that one should use a heat gun or good hair dryer to warm the paint a little before beginning the process. This should help prevent cracks in the finish during the rolling process, which will lead to rust in the future.
Best wishes.
Best wishes.
Registered User
Texasscout
Registered User
close
- Join DateFeb 2005
- LocationSouth Texas
- Posts:35,605
-
iTrader Positive Feedback100
-
iTrader Feedback Score(11)
-
Likes:1,583
-
Liked:2,116 Times in 1,768 Posts
The MAIN THING to remember: Use a heat gun to soften the paint before and during the rolling!!!!! You WILL crack/chip/flake the paint if you don't. You must keep it hot as you roll the fender.
Registered User
gary c
Registered User
close
- Join DateFeb 2005
- LocationValencia, Ca
- Posts:19,433
-
iTrader Positive Feedback100
-
iTrader Feedback Score(10)
-
Likes:69
-
Liked:1,133 Times in 1,003 Posts
Quote:
Like I posted, "Old School" that's how we rolled fenders before they made a machine that does it easier....baseball bat or large diameter steel pipe. Hair dryers, no way we used the sun and took our time.Originally Posted by bjquinnIUmed
I don't think the phrase "baseball bat" should enter a tips thread on successful DIY fender rolling...
Gary
Registered User
^he also added a caveat on keeping the fenders hot WHILE rolling, which I think is a good tip.
Registered User
gary c
Registered User
close
- Join DateFeb 2005
- LocationValencia, Ca
- Posts:19,433
-
iTrader Positive Feedback100
-
iTrader Feedback Score(10)
-
Likes:69
-
Liked:1,133 Times in 1,003 Posts
Quote:
Yea, you tree dwellers get really pissed when our caves are warm at night and you're freezin your azz's off....Originally Posted by ZMonkey11
^he also added a caveat on keeping the fenders hot WHILE rolling, which I think is a good tip.

Gary