Answer a few of my questions please ?
#1
Answer a few of my questions please ?
My 06 G35😍
So I have g37 wheels on and I'm using the oem lugs or acorn style idk if it's the same or not but either way they're holding fine and I drive hard trust me . 1 lug on both sides of rear are starting to round and I can't tighten any more to have it seat 100% as it should so it gets loose here and here. I need someone who is running some after market to point me in the right direction rather than the " oem g37 lugs only" because these are holding out fine and have no problems if it wasn't for it being rounded .. So please chime in . And just so I know what are the exact lugs I will need to make these fit as they should as oem so many unclear threads and post .
Also I just installed berks hfc they sound beautiful until I let off the gas and it sounds like a maraca under my car lol ..I hear a hiss and I'm fine with that but what about the maracas under my car ? Lol What's the deal ? . And ses just came on but I forgot to reset ecu, throttle and air .. So I did that today hoping it was just needing a reset . My butt dyno is saying add about 10 hp 😏👌
Last edited by bennyjoel; 04-30-2015 at 12:11 AM.
#2
1. I hate you for running the same wheels as me, thought I was the only OB coupe running the 37s.
2. Get a set of the stock spline lugs and ditch those acorn ones.
3. You really shouldn't be hearing hissing from the exhaust, that would point to a leak. Lift the car back up and double check all the gaskets and bolts.
4. Reset the ECU again (negative side disconnected for a good 15min)
2. Get a set of the stock spline lugs and ditch those acorn ones.
3. You really shouldn't be hearing hissing from the exhaust, that would point to a leak. Lift the car back up and double check all the gaskets and bolts.
4. Reset the ECU again (negative side disconnected for a good 15min)
#3
Registered User
iTrader: (10)
1. I hate you for running the same wheels as me, thought I was the only OB coupe running the 37s.
2. Get a set of the stock spline lugs and ditch those acorn ones.
3. You really shouldn't be hearing hissing from the exhaust, that would point to a leak. Lift the car back up and double check all the gaskets and bolts.
4. Reset the ECU again (negative side disconnected for a good 15min)
2. Get a set of the stock spline lugs and ditch those acorn ones.
3. You really shouldn't be hearing hissing from the exhaust, that would point to a leak. Lift the car back up and double check all the gaskets and bolts.
4. Reset the ECU again (negative side disconnected for a good 15min)
Gary
#5
Haha I really thought I was the only one with them on a OB .
So okay I'll lose the acorn lugs .. Could I grab any spline off the Internet likeee EBAY hehe .. I want blue lugs :'(.. or am I going to really have to get the "stock g37 lugs" anyone have luck painting them ?
Yea I've been reading on berks and videos and everyone's has a hiss that comes from back pressure? At least that's what I've been reading .. I will get under the car and double check every bolt .. See if I could squeeze a bit more on the cat to header bolts too but I'm pretty solid when it comes to getting good seal. It Sounds sorta like a BOV lol ... I'll post a video on my break .. Have you had a berk hfc sound completely clear with no "metallic" sound and or hiss? Jw
For resetting the ECU I read that you only need to disconnect the neg for 3 minutes and that's what I did previously before i read your comment and my ses went away .. Will 15 mins make it reset better lol dumb questions sorry
So okay I'll lose the acorn lugs .. Could I grab any spline off the Internet likeee EBAY hehe .. I want blue lugs :'(.. or am I going to really have to get the "stock g37 lugs" anyone have luck painting them ?
Yea I've been reading on berks and videos and everyone's has a hiss that comes from back pressure? At least that's what I've been reading .. I will get under the car and double check every bolt .. See if I could squeeze a bit more on the cat to header bolts too but I'm pretty solid when it comes to getting good seal. It Sounds sorta like a BOV lol ... I'll post a video on my break .. Have you had a berk hfc sound completely clear with no "metallic" sound and or hiss? Jw
For resetting the ECU I read that you only need to disconnect the neg for 3 minutes and that's what I did previously before i read your comment and my ses went away .. Will 15 mins make it reset better lol dumb questions sorry
Last edited by bennyjoel; 04-30-2015 at 11:34 AM.
#7
i know that after I do this manual shifts hit hard as rocks so it is defiantly clearing the fuel map and shift timing.
Trending Topics
#8
So I have g37 wheels on and I'm using the oem lugs or acorn style idk if it's the same or not but either way they're holding fine and I drive hard trust me . 1 lug on both sides of rear are starting to round and I can't tighten any more to have it seat 100% as it should so it gets loose here and here. I need someone who is running some after market to point me in the right direction rather than the " oem g37 lugs only" because these are holding out fine and have no problems if it wasn't for it being rounded .. So please chime in . And just so I know what are the exact lugs I will need to make these fit as they should as oem so many unclear threads and post .
You really can't say they are working fine if you are having problems.
#9
Well If it wasn't rounded it would allow me to tighten it all the way.. But either way it's the wrong one anyway .
Also do you think the autozone spline 12x1.25 will be fine ?
I have another problem ... Who ever owned the car before me bottomed out and snapped the plastic off the bottom cover and the screws and bracket nuts are just barely holding on here's my problem in a picture
The top is the bumper and bottom is the bottom cover .. there's suppose to be a complete circle on the bottom of the bumper to hold better but it's missing probably snapped off .... This is has happened to several of the Holes on the bottom of the bumper ..
I'm about ready to buy a whole bumper because of this
Also do you think the autozone spline 12x1.25 will be fine ?
I have another problem ... Who ever owned the car before me bottomed out and snapped the plastic off the bottom cover and the screws and bracket nuts are just barely holding on here's my problem in a picture
The top is the bumper and bottom is the bottom cover .. there's suppose to be a complete circle on the bottom of the bumper to hold better but it's missing probably snapped off .... This is has happened to several of the Holes on the bottom of the bumper ..
I'm about ready to buy a whole bumper because of this
#11
#12
I am going to guess that the hissing is only when coasting and the RPM's are between say around 2800 down to 2000 if that is correct then I had the same thing happen on my Z when I put in test pipes. My current car has stock cats but if I listen very carefully I can still slightly and I mean ever so slightly hear the same noise almost like a bearing whistling, If this is the case I wouldn't worry about it. I drove my Z all the way to 180k miles never had a problem just was really odd.
#13
#15