Driver door rubber strip
Driver door rubber strip
well I ripped mine and now a portion of the top part is not there, the little part that overlaps uptop, is this a DIY able? Can I get this piece solo or do I need to go to a dealer.
thanks
thanks
Last edited by thescreensavers; Jun 20, 2009 at 11:51 PM.
Registered User
Joined: Jun 2009
Posts: 30
Likes: 0
From: feenicks
I was trying to find one of the seals for the door, the weather strip that attaches to the body, but couldn't find it on the part break down over at Riverside.
I'd suggest just asking your local friendly Infiniti dealer and they'll know the part number. That's who you'll have to buy from anyway.
...and that last sentence was foreshadowing of my own
I'd suggest just asking your local friendly Infiniti dealer and they'll know the part number. That's who you'll have to buy from anyway.
...and that last sentence was foreshadowing of my own
I was trying to find one of the seals for the door, the weather strip that attaches to the body, but couldn't find it on the part break down over at Riverside.
I'd suggest just asking your local friendly Infiniti dealer and they'll know the part number. That's who you'll have to buy from anyway.
...and that last sentence was foreshadowing of my own
I'd suggest just asking your local friendly Infiniti dealer and they'll know the part number. That's who you'll have to buy from anyway.
...and that last sentence was foreshadowing of my own
Does anyone know how to install this part. The labor rate here is like 130.
Trending Topics
I assume this also, but I don't know how easy it is to install. I hope someone can post up how. I am going to call the dealer now to find out how much.
Registered User
Joined: May 2009
Posts: 471
Likes: 2
they're easy to do. a few clips, a few strips of double sided tape.
much easier once you have the new strips in hand. easier to see what you're dealing with.
clean up the old tape residue thoroughly. dont pull the backing off the new adhesive until you are clipped into place.
to get the strip into the top groove, stand on the inner side of the door and work the inside edge in first. I might be thinking of the v36, but I'm pretty sure the v35 has the same set up.
cheers
much easier once you have the new strips in hand. easier to see what you're dealing with.
clean up the old tape residue thoroughly. dont pull the backing off the new adhesive until you are clipped into place.
to get the strip into the top groove, stand on the inner side of the door and work the inside edge in first. I might be thinking of the v36, but I'm pretty sure the v35 has the same set up.
cheers
they're easy to do. a few clips, a few strips of double sided tape.
much easier once you have the new strips in hand. easier to see what you're dealing with.
clean up the old tape residue thoroughly. dont pull the backing off the new adhesive until you are clipped into place.
to get the strip into the top groove, stand on the inner side of the door and work the inside edge in first. I might be thinking of the v36, but I'm pretty sure the v35 has the same set up.
cheers
much easier once you have the new strips in hand. easier to see what you're dealing with.
clean up the old tape residue thoroughly. dont pull the backing off the new adhesive until you are clipped into place.
to get the strip into the top groove, stand on the inner side of the door and work the inside edge in first. I might be thinking of the v36, but I'm pretty sure the v35 has the same set up.
cheers
Thanks
Ok so I found out a site that sells these parts and I can get it for 90 shipped
http://www.infinitipartsusa.com/part...layCatalogid=0
I am pretty sure #5 is the right part.
Also If someone could explain the installation and uninstall procedure?
Thanks
http://www.infinitipartsusa.com/part...layCatalogid=0
I am pretty sure #5 is the right part.
Also If someone could explain the installation and uninstall procedure?
Thanks
Thread
Thread Starter
Forum
Replies
Last Post
