Random Little Question Thread
#4996
#4998
So, my heating is reeealy smelly(03 sedan). Do i need one of these?
http://www.autopartswarehouse.com/de...EPN420101.html
or
http://www.autopartswarehouse.com/de...EPN420104.html
If so, which one would you recommend?
http://www.autopartswarehouse.com/de...EPN420101.html
or
http://www.autopartswarehouse.com/de...EPN420104.html
If so, which one would you recommend?
#5000
I was exaggerating a little bit lol, it's not dead mouse bad, but it is a little unpleasant.(watch me find a dead mouse in there now haha). But thanks
#5001
#5002
#5003
ill Sedan
iTrader: (87)
Dave, I went through 2 OEM undertrays and countless times of repairing them. It got to the point where the OEM one just wouldn't sit high enough and would be dragging everywhere.. I've been running the RareJDM under panel for over a year. Because I'm slammed I've installed it so that it sits higher than OEM. Instead of attaching it to the bottom of the bumper up front like the OEM one I made it so that it sits above the bumper against the frame (if that makes sense (its not attached to the front bumper). I've banged and scraped the under panel pretty hard on countless occasions and there isn't even a single dent in it, just some scratches.
#5004
ill Sedan
iTrader: (87)
#5005
ill Sedan
iTrader: (87)
When I added my Koyo radiator I had to add a tranny cooler, RRYDE made a nice bracket for me so it sits right behind the opening in my KuRookie bumper:
#5006
Dave, I went through 2 OEM undertrays and countless times of repairing them. It got to the point where the OEM one just wouldn't sit high enough and would be dragging everywhere.. I've been running the RareJDM under panel for over a year. Because I'm slammed I've installed it so that it sits higher than OEM. Instead of attaching it to the bottom of the bumper up front like the OEM one I made it so that it sits above the bumper against the frame (if that makes sense (its not attached to the front bumper). I've banged and scraped the under panel pretty hard on countless occasions and there isn't even a single dent in it, just some scratches.
http://www.zspeedperformance.com/03-09-350Z-03-06-G35-SDN-Aluminum-Engine-Undershrouds-V2-ZSP2001.htm
#5007
I drove ttrank's car solo
iTrader: (50)
Join Date: Mar 2009
Location: By the sea, Tx
Posts: 18,299
Received 1,486 Likes
on
1,221 Posts
G35 sedan w/ too much money in mods
^^That's the one I have although I'm on my second one. I hit a tire tread about 18X18" square a while back going 60 in rush hour traffic and this is the effect of the impact on my first Z Speed.
The impact ripped the front of the tray from my bumper and bent it backwards 180 degrees and I drove the last mile and a half dragging the damn thing on the road. I'm too low to get under it and try to bend it back for the rest of my drive home.
The impact ripped the front of the tray from my bumper and bent it backwards 180 degrees and I drove the last mile and a half dragging the damn thing on the road. I'm too low to get under it and try to bend it back for the rest of my drive home.
#5009
I drove ttrank's car solo
iTrader: (50)
Join Date: Mar 2009
Location: By the sea, Tx
Posts: 18,299
Received 1,486 Likes
on
1,221 Posts
G35 sedan w/ too much money in mods
Bumper no, but the impact punched a U shaped piece of my front lip in and put a 3" dent in the lip as well. I just popped the punched part back out so it looks OK from a distance but is very noticeable up close. My whole front end is sad looking at almost 100K miles with tons of rock chips and wear, so I'm looking at an 05-06 poly Nismo replica to go on next spring. I'm going to have my lip repaired and molded onto the new bumper at the same time.
#5010
ill Sedan
iTrader: (87)
Is this the under tray I'm planning on buying one
http://www.zspeedperformance.com/03-...V2-ZSP2001.htm
http://www.zspeedperformance.com/03-...V2-ZSP2001.htm
http://www.injectedperformance.com/r...for350zg35.htm
http://www.z1auto.com/prodmore.asp?m...or&prodid=4911