Aggressive Wheels & Stretched Tires: Post 'Em Up! [[Some NSFW]]
#7880
Registered User
iTrader: (60)
no.... My cars in peices right now, the whole kit is off, and they are doing a wire tuck so the car will be there for a while, so they are gonna do it. 2C and Levon (Street Works) has special for 2800 for bags with everything needed and installed by Shane
Last edited by 4drmadness; 01-08-2010 at 01:18 PM.
#7881
The stuff Jessie was working on last night will turn out awesome..I should've jumped on those since they were initially offered to me.
#7885
#7886
#7887
Former G35driver Vendor
iTrader: (84)
The offset on the front was +17. I'm using the rear barrels that had on offset of +18 with the center from the front and according to my measurement the pad is also 18mm thicker than the pad originally. Does that make it 10.5+0? The rear wheels are getting an entirely new treatement.
#7888
ill Sedan
iTrader: (87)
#7890
The goblin resurrection
iTrader: (66)
Measuring Wheel Offset
To calculate offset you'll need the following measurements:
<!--mstheme--><!--msthemelist--><TABLE cellSpacing=0 cellPadding=0 width="100%" border=0><!--msthemelist--><TBODY><TR><TD vAlign=baseline width=42></TD><TD vAlign=top width="100%"><!--mstheme-->Wheel backspace<!--mstheme--><!--msthemelist--></TD></TR><!--msthemelist--><TR><TD vAlign=baseline width=42></TD><TD vAlign=top width="100%"><!--mstheme-->Wheel Width<!--mstheme--><!--msthemelist--></TD></TR><!--msthemelist--><TR><TD vAlign=baseline width=42></TD><TD vAlign=top width="100%"><!--mstheme-->Wheel Center line (outboard flange to inboard flange measurement / 2)<!--mstheme--><!--msthemelist--></TD></TR><!--msthemelist--></TBODY></TABLE><!--mstheme-->
Subtract:
<!--mstheme--><!--msthemelist--><TABLE cellSpacing=0 cellPadding=0 width="100%" border=0><!--msthemelist--><TBODY><TR><TD vAlign=baseline width=42></TD><TD vAlign=top width="100%"><!--mstheme-->Wheel center line from Wheel backspace to get offset. <!--mstheme--><!--msthemelist--><TABLE cellSpacing=0 cellPadding=0 width="100%" border=0><!--msthemelist--><TBODY><TR><TD vAlign=baseline width=42></TD><TD vAlign=top width="100%"><!--mstheme-->If backspace is less than the wheel centerline the offset is negative<!--mstheme--><!--msthemelist--></TD></TR><!--msthemelist--><TR><TD vAlign=baseline width=42></TD><TD vAlign=top width="100%"><!--mstheme-->If backspace is greater than the wheel centerline the offset is positive<!--mstheme--><!--msthemelist--></TD></TR><!--msthemelist--></TBODY></TABLE><!--mstheme--><!--mstheme--><!--msthemelist--></TD></TR><!--msthemelist--></TBODY></TABLE><!--mstheme-->
Tip:
<!--mstheme--><!--msthemelist--><TABLE cellSpacing=0 cellPadding=0 width="100%" border=0><!--msthemelist--><TBODY><TR><TD vAlign=baseline width=42></TD><TD vAlign=top width="100%"><!--mstheme-->To convert from inches to mm multiply by 25.4<!--mstheme--><!--msthemelist--></TD></TR><!--msthemelist--><TR><TD vAlign=baseline width=42></TD><TD vAlign=top width="100%"><!--mstheme-->To convert from mm to inches divide by 25.4</TD></TR></TBODY></TABLE>
Last edited by GreenGoblin; 01-08-2010 at 04:17 PM.