Osiris price drop in Standard Version
#1
Osiris price drop in Standard Version
Take a look:
http://secure.uprev.com/osiris-standard.html
Very tempting to see if any gains are met and if they are better than my current BD.
The price of the Cobb is $695.00 and it does not offer a lot of parameters like this one:
* Up to 5 Maps on cruise control equipped vehicles
* Idle RPM
* Speed Limiter
* Electronic Throttle Control to achieve Wide Open Throttle at all speeds.
* Rev Limiter
* DTC disable
* AFR Targets
* Fuel Compensation
* Ignition Timing Advance
* Cam Phasing for equipped vehicles.
Opinions ???
http://secure.uprev.com/osiris-standard.html
Very tempting to see if any gains are met and if they are better than my current BD.
The price of the Cobb is $695.00 and it does not offer a lot of parameters like this one:
* Up to 5 Maps on cruise control equipped vehicles
* Idle RPM
* Speed Limiter
* Electronic Throttle Control to achieve Wide Open Throttle at all speeds.
* Rev Limiter
* DTC disable
* AFR Targets
* Fuel Compensation
* Ignition Timing Advance
* Cam Phasing for equipped vehicles.
Opinions ???
#2
I had almost bought the Cobbtuning, I actually did buy it but had them cancel it. I ran across Osiris and they look a lot better. Some of the developers of cobbtuning left to go over to Osiris. I have an apointment Wed. at 1 to get my tune! I cant wait....are our g's equipped for cam phasing?
here a link with a guy who has it and set his to a 8500 redline
here a link with a guy who has it and set his to a 8500 redline
#3
Why do we have to give them VIN ? ECU part number sounds reasonable but giving out VIN makes me worry.
Setting VQ35HR to 8500rpm red line without any internal upgrade is scary. If you happen to know the guy, ask him how many miles he has run the car with his new setup and how his driving is.
Setting VQ35HR to 8500rpm red line without any internal upgrade is scary. If you happen to know the guy, ask him how many miles he has run the car with his new setup and how his driving is.
#7
Trending Topics
#8
Osiris - Engine Management
Ok, I mistakenly got this video confused
with a someone, who i'm friends with on youtube who got the uprev tune at the same shop where I went heres hes vid below
/hackme88#p/u/1/ysM7YmrALsA
S&R performance in Tampa,Fla. Bobby took really good care of me! sandrperformance.com
It took about 2hrs and I was done real simple and easy, they plug right into your ECU through your cig lighter.
About 20whp to the wheels were gained in my tune, the torque is increased very noticeably under 3k and all around I love it!! The redline was raised a few100rpms. and the governor was set to 300mph lol jk but really no governor. I do not regret doing this. 32.5 $ per horsepower!!
Oh btw I had an intake on for about 3 weeks before this and the Air-to-fuel ratio had to be adjusted by 10% on the computer.
Thanks Uprev and Bobby!!
with a someone, who i'm friends with on youtube who got the uprev tune at the same shop where I went heres hes vid below
S&R performance in Tampa,Fla. Bobby took really good care of me! sandrperformance.com
It took about 2hrs and I was done real simple and easy, they plug right into your ECU through your cig lighter.
About 20whp to the wheels were gained in my tune, the torque is increased very noticeably under 3k and all around I love it!! The redline was raised a few100rpms. and the governor was set to 300mph lol jk but really no governor. I do not regret doing this. 32.5 $ per horsepower!!
Oh btw I had an intake on for about 3 weeks before this and the Air-to-fuel ratio had to be adjusted by 10% on the computer.
Thanks Uprev and Bobby!!
Last edited by LakeShore_Slate; 10-27-2009 at 11:30 PM. Reason: not to no
#12
If you go on the site uprev.com you can watch how they install it into the ECU takes around 3 min. for the process to be done. Afterwards we did the baseline dyno pull and a few pulls after that just having some fun. so it can be done really quickly if you'd like.
oh ya plus i was having fun looking at all the turbo cars they had at the shop!
for the standard tune with osirius software installed it was 650 which is what i had them do. if you already have the software install its 450. dyno'n is included in that number.
oh ya plus i was having fun looking at all the turbo cars they had at the shop!
congrats on these good numbers.
how much did you pay for the dyno?
how much did you pay for the dyno?
#14
I had almost bought the Cobbtuning, I actually did buy it but had them cancel it. I ran across Osiris and they look a lot better. Some of the developers of cobbtuning left to go over to Osiris. I have an apointment Wed. at 1 to get my tune! I cant wait....are our g's equipped for cam phasing?
here a link with a guy who has it and set his to a 8500 redline
http://www.youtube.com/watch?v=LKKYP...eature=related
here a link with a guy who has it and set his to a 8500 redline
http://www.youtube.com/watch?v=LKKYP...eature=related
especially from 1 to 2, hmmmm got me very interested.
#15
I had almost bought the Cobbtuning, I actually did buy it but had them cancel it. I ran across Osiris and they look a lot better. Some of the developers of cobbtuning left to go over to Osiris. I have an apointment Wed. at 1 to get my tune! I cant wait....are our g's equipped for cam phasing?
here a link with a guy who has it and set his to a 8500 redline
http://www.youtube.com/watch?v=LKKYP...eature=related
here a link with a guy who has it and set his to a 8500 redline
http://www.youtube.com/watch?v=LKKYP...eature=related
https://g35driver.com/forums/v36-eng...elp-techs.html