Feeler: Ings Face Ducts
#1
03-11-2009, 02:08 AM
Join Date: May 2005
Location: 909/626 California
Posts: 1,770
Likes: 0
Received 0 Likes
on
0 Posts
Feeler: Ings Face Ducts
***SOLD***
The orginal Ings Face ducts are $475, and the fitment isnt as good. These had to be tweaked to fit better than the original ducts.
The orginal Ings Face ducts are $475, and the fitment isnt as good. These had to be tweaked to fit better than the original ducts.
Last edited by Silverbolt; 04-28-2009 at 12:26 AM.
#2
03-11-2009, 02:11 AM
Join Date: May 2005
Location: 909/626 California
Posts: 1,770
Likes: 0
Received 0 Likes
on
0 Posts
This is what I said in my review thread:
Now after taking some test fit pictures, I'm even more impressed, and I cant wait to sand down the bottom of mine so it fits with my molded ings lip!!! When I held it on, it just seemed to fit right in place. There were a few little gaps, but thats to be expected when I'm holding it on with my fingers. If I installed it with the double sided tape, it would eliminate the gaps. Here are the pictures.
As you can see, the fitment is dead on!
As you can see, the fitment is dead on!
Last edited by Silverbolt; 03-11-2009 at 02:20 AM.
#3
03-11-2009, 02:12 AM
Join Date: May 2005
Location: 909/626 California
Posts: 1,770
Likes: 0
Received 0 Likes
on
0 Posts
enjoy the pics
ENJOY!!!Last edited by Silverbolt; 03-11-2009 at 02:19 AM.
#4
03-11-2009, 02:15 AM
Join Date: May 2005
Location: 909/626 California
Posts: 1,770
Likes: 0
Received 0 Likes
on
0 Posts
Before I installed them, I wanted to take a few more pictures. I stuck the passenger side in, and not the driver side, so we can compare and look at the differences the face ducts make. Keep in mind that I didnt put any double sided tape, and I just stuck them in, thats why it looks like there are gaps. I'll post some pictures of the finish install in a little bit...
#5
03-11-2009, 02:17 AM
Join Date: May 2005
Location: 909/626 California
Posts: 1,770
Likes: 0
Received 0 Likes
on
0 Posts
Now here are the final installed pictures. And the curve that I mentioned before. At the bottom of the face ducts, towards the center, it curves up a little. It looks like it curves a little too much. I had problems getting the double sided tape to hold it down. It still doesnt hold it down all the way, but no one can realy tell though. I might be having this problem, only because I molded my front lip, which doesnt allow me much play to wiggle the face ducts to fit right. Either way, I dont think its a problem. Its on snug, and the install was actually alot easier than I thought! Enjoy the pictures!
AHHH... DONT LOOK AT MY ROCK CHIPS!!!!!
AHHH... DONT LOOK AT MY ROCK CHIPS!!!!!
#6
03-11-2009, 02:18 AM
Join Date: May 2005
Location: 909/626 California
Posts: 1,770
Likes: 0
Received 0 Likes
on
0 Posts
Trending Topics
haha
#13
03-11-2009, 05:08 PM
Join Date: May 2005
Location: 909/626 California
Posts: 1,770
Likes: 0
Received 0 Likes
on
0 Posts
*EDIT TO LISTING*
I havent decided for sure yet, if I'm going to sell them. It depends on how much the offers will be... so let me know
The OG ones are sold for $475, and you probably wont find any copies. Make me an offer.
I havent decided for sure yet, if I'm going to sell them. It depends on how much the offers will be... so let me know
The OG ones are sold for $475, and you probably wont find any copies. Make me an offer.
Last edited by Silverbolt; 03-11-2009 at 05:33 PM.
