Relentless Autosports Strut Bar - (NOT VRT!)
#421
01-30-2009, 08:51 AM
A/C line is easy, just take your time.
It's aluminum tubing & is very soft & easy to reshape.
One trick is to get a short piece of neoprene tubing (2 -3 ") then slice it lengthwise.
You then slide it over the tubing.
It helps spread the load on the A/C line as you bend it.
= smoother bend & less chance of damage.
#422
01-30-2009, 03:56 PM
sorry.... falling behind on this thread.
A/C line is easy, just take your time.
It's aluminum tubing & is very soft & easy to reshape.
One trick is to get a short piece of neoprene tubing (2 -3 ") then slice it lengthwise.
You then slide it over the tubing.
It helps spread the load on the A/C line as you bend it.
= smoother bend & less chance of damage.
A/C line is easy, just take your time.
It's aluminum tubing & is very soft & easy to reshape.
One trick is to get a short piece of neoprene tubing (2 -3 ") then slice it lengthwise.
You then slide it over the tubing.
It helps spread the load on the A/C line as you bend it.
= smoother bend & less chance of damage.
#424
01-30-2009, 06:51 PM
Heard from Scott today. Mine's paid in full and hopefully should be shipping in the next week or two. Woohoo!
#426
01-31-2009, 09:04 PM
I spent 3 or so hours with scott and his fabricator last wednesday. They got the brackets all mocked up for us vortech guys and nice little RA plaques for the middle of the bar. I believe the bars should be going to paint earlier this week, so you guys will have your bars very soon.
-cheers!
-cheers!
#427
01-31-2009, 09:12 PM
He told me the same thing on Friday. Looking forward to getting it. Not looking forward the DIY mod required to get it to work with the Stillen intake.
#431
02-01-2009, 02:12 PM
For you guys stuck on keeping the OE air box....
I believe it would not be that difficult to do.
The only part that interferes is the nut where the lower arm brace mounts to the suspension point. (beside arrow on the left)
With all the aftermarket intakes installed, there must be a ton of old air boxes available for next to nothing.
I'd be picking one up to play with.
I never actually got around to it,
but I think all it would take is a heat gun to reshape the box a bit where that nut goes.
I believe it would not be that difficult to do.
The only part that interferes is the nut where the lower arm brace mounts to the suspension point. (beside arrow on the left)
With all the aftermarket intakes installed, there must be a ton of old air boxes available for next to nothing.
I'd be picking one up to play with.
I never actually got around to it,
but I think all it would take is a heat gun to reshape the box a bit where that nut goes.
#432
02-03-2009, 10:57 PM
can't wait can't wait can't wait can't wait can't wait can't wait can't wait can't wait...
aw hell yes i can. i'm outta town until march. which reminds me...
Jordan or Scott is it possible to delay shipping until about the time i get back? i won't be here to receive it and fear it will be returned. i'll pm.
aw hell yes i can. i'm outta town until march. which reminds me...
Jordan or Scott is it possible to delay shipping until about the time i get back? i won't be here to receive it and fear it will be returned. i'll pm.
#433
02-04-2009, 02:59 AM
My final payment is finally in!
I'm dreaming of the day I get back home and find my RA strut bar.
If it's even half as good as Integr8r says...
I'm dreaming of the day I get back home and find my RA strut bar.
If it's even half as good as Integr8r says...
