Not starting
#1
07-23-2018, 05:46 PM
Join Date: Jun 2018
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
#3
07-23-2018, 09:49 PM
Join Date: Mar 2009
Location: By the sea, Tx
Posts: 18,301
Received 1,486 Likes
on
1,221 Posts
G35 sedan w/ too much money in mods
SMDH at these kinds of posts.
OP how the hell do you expect us to have any suggestions for you with the limited information you posted. Please be more thorough explaining what the car's doing, what work if any has been done to it recently, when did your problem start, how many miles are on the car or put on after any work was done to it, are any warning/SES lights lit up on the dash when you try to start it, etc.
OP how the hell do you expect us to have any suggestions for you with the limited information you posted. Please be more thorough explaining what the car's doing, what work if any has been done to it recently, when did your problem start, how many miles are on the car or put on after any work was done to it, are any warning/SES lights lit up on the dash when you try to start it, etc.
#4
07-23-2018, 10:02 PM
Join Date: Jun 2018
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
#5
07-23-2018, 10:47 PM
Join Date: May 2017
Location: Washington State
Posts: 14,790
Received 2,456 Likes
on
2,150 Posts
Coupe 6MT Premium RAS
So I'm just guessing since you provided almost no details but here's what I think is happening.
-You CLUTCH was slipping (flywheel doesn't slip, the clutch does).
-You took the car to Nissan for a new clutch and possible a new flywheel.
-Nissan replaced the components
-Now the car won't start.
Now if Nissan did take the flywheel off then they probably didn't put it on correctly, there is an alignment pin that MUST be lined up on the flywheel for the engine to start, ask them if they bothered to check the flywheel alignment pin. Refer them to section EM page 149 under cylinder block assembly for pictures and directions on how to PROPERLY install the flywheel.
-You CLUTCH was slipping (flywheel doesn't slip, the clutch does).
-You took the car to Nissan for a new clutch and possible a new flywheel.
-Nissan replaced the components
-Now the car won't start.
Now if Nissan did take the flywheel off then they probably didn't put it on correctly, there is an alignment pin that MUST be lined up on the flywheel for the engine to start, ask them if they bothered to check the flywheel alignment pin. Refer them to section EM page 149 under cylinder block assembly for pictures and directions on how to PROPERLY install the flywheel.
The following users liked this post:
Scorpi0 (07-24-2018)
#6
07-23-2018, 10:49 PM
Join Date: May 2017
Location: Washington State
Posts: 14,790
Received 2,456 Likes
on
2,150 Posts
Coupe 6MT Premium RAS
#7
07-23-2018, 10:50 PM
Join Date: May 2017
Location: Washington State
Posts: 14,790
Received 2,456 Likes
on
2,150 Posts
Coupe 6MT Premium RAS
Trending Topics
#8
07-24-2018, 06:48 AM
Join Date: Mar 2009
Location: By the sea, Tx
Posts: 18,301
Received 1,486 Likes
on
1,221 Posts
G35 sedan w/ too much money in mods
Thread
Thread Starter
Forum
Replies
Last Post
trini35
G35 Sedan V35 2003-06
21
12-11-2023 05:00 PM
tnguyen
Audio, Video & Electronics
5
08-17-2014 12:33 PM
BolivianFuego
G35 Coupe V35 2003 - 07
10
02-13-2013 12:01 AM