Who changed the Inven?
I really wanted the Inven from Eric. It's the only front bumper I've seen that I absolutely love!
#64
02-13-2011, 09:53 PM
#65
02-13-2011, 11:42 PM
whatever shop did the bodywork on that second pic either did a shi**y job or that car was in some sort of front end accident. also on that second pic, why is the top of his headlight sunk into the fender like that and the corner of the fender bent in? did his shop do that to make the bumper fit better or was it due to a previous accident? I have the revised version and it doesn't look anywhere near that bad. I just need to fix that one place where the tip of the fender rubbed too hard on the bumper and pushed the paint up like that.
Last edited by psycobusa; 02-13-2011 at 11:48 PM.
#66
02-28-2011, 01:09 PM
BUMP! Get in on this group buy - our original folks are not jumping on this - we need some more people! Take a look:
https://g35driver.com/forums/interio...ndustries.html
https://g35driver.com/forums/interio...ndustries.html
#67
02-28-2011, 01:29 PM
HOLY CRAP !!!!!!!!!
That is some of the worst fitment I have ever seen in my life.
Who ever redisigned the bumper and added that fugly shelf should be shot, also the quality control is horrible.
If I was paying for the first one and I recieved the second one in the mail, I would be pissed.
#68
02-28-2011, 01:32 PM
#71
03-01-2011, 07:47 AM
#72
08-08-2011, 06:42 PM
I believe that is a new mold from VIS and the reason I say that, is because I bought it from them and thats how it looks...misalignment pretty much everywhere.
what you will get is:
***misalignment on the tabs under the grille (too short)
***misalignment on the fender (see below side shot)
***tabs that fasten bumper to the car just under the hood, are not long enough and will need a lay-on extensions of about an INCH, to be able to even put a clip in to hold it in place
***hood will hit the bumper upon closing
***vents would need to be trimmed to get a closer, yet still not close enough fitment.
***bumper may come with cracks, as it came to me, so get your bondo out
***bumper is not pre-drilled.
Bottom line, lots of tweaking to do, which bodyshop will gladly charge you for
If don't have the pics uploaded on photobucket, but can send them to your e mail if you want to see what I am talking about.
PM me your E-Mail if you want.
what you will get is:
***misalignment on the tabs under the grille (too short)
***misalignment on the fender (see below side shot)
***tabs that fasten bumper to the car just under the hood, are not long enough and will need a lay-on extensions of about an INCH, to be able to even put a clip in to hold it in place
***hood will hit the bumper upon closing
***vents would need to be trimmed to get a closer, yet still not close enough fitment.
***bumper may come with cracks, as it came to me, so get your bondo out
***bumper is not pre-drilled.
Bottom line, lots of tweaking to do, which bodyshop will gladly charge you for
If don't have the pics uploaded on photobucket, but can send them to your e mail if you want to see what I am talking about.
PM me your E-Mail if you want.
#73
08-08-2011, 08:19 PM
Join Date: Apr 2011
Location: 2115 Troy Ave South El Monte CA 91773
Posts: 1,657
Received 239 Likes
on
159 Posts
*subscribed*? lol
The following users liked this post:
ThatOneDude (08-09-2011)
Thread
Thread Starter
Forum
Replies
Last Post
n2fooz
Engine, Drivetrain & Forced-Induction
0
09-04-2015 07:46 PM
