OFFICIAL: Aggressive Wheel fitment FLUSH/STRETCH sedan

Thread Tools
 
Search this Thread
 
Rating: Thread Rating: 7 votes, 5.00 average.
 
Old Jul 4, 2010 | 08:29 PM
  #1036  
SN00P's Avatar
CLUB MODERATOR
iTrader: (21)
Joined: Jan 2010
Posts: 8,028
Likes: 118
From: Florida G club
marcus how much did you pull the rears to get a +10

whats the lowest offset i can pull off with either a 225/35 or a 235/35 in the rear without pulling ...
 
Reply
Old Jul 4, 2010 | 08:39 PM
  #1037  
CandlestickPark's Avatar
ill Sedan
Staff Alumni
iTrader: (87)
Joined: Jun 2007
Posts: 23,261
Likes: 2,688
From: Long Beach, SoCal
Premier Member

Originally Posted by FlyingLumpia
I am running 19x9 +12 now. With a 225/40

Yeah or maybe a two tone like Levon. But I dont want to copy him.

Man if I didnt get that MRI bill, I would have a few different things. Maybe a new wheel setup.
Depending on your camber/ride height you'll have to do some fender work to add 5mm more to a 19x9 +12. I bet it looks good as is, looking forward to pics.
 
Reply
Old Jul 4, 2010 | 08:42 PM
  #1038  
CandlestickPark's Avatar
ill Sedan
Staff Alumni
iTrader: (87)
Joined: Jun 2007
Posts: 23,261
Likes: 2,688
From: Long Beach, SoCal
Premier Member

Originally Posted by g35snoop
marcus how much did you pull the rears to get a +10

whats the lowest offset i can pull off with either a 225/35 or a 235/35 in the rear without pulling ...
My rears are pulled 5mm. Assuming a very flat roll, on a 9.5 you could go to +15 without pulling with a 235/35 and +10 with a 225/35. That is assuming about 3.5 to 4 degrees of negative camber.
 
Reply
Old Jul 4, 2010 | 08:44 PM
  #1039  
SN00P's Avatar
CLUB MODERATOR
iTrader: (21)
Joined: Jan 2010
Posts: 8,028
Likes: 118
From: Florida G club
...
 

Last edited by SN00P; Jul 4, 2010 at 08:52 PM.
Reply
Old Jul 4, 2010 | 08:52 PM
  #1040  
SN00P's Avatar
CLUB MODERATOR
iTrader: (21)
Joined: Jan 2010
Posts: 8,028
Likes: 118
From: Florida G club
Originally Posted by CandlestickPark
My rears are pulled 5mm. Assuming a very flat roll, on a 9.5 you could go to +15 without pulling with a 235/35 and +10 with a 225/35. That is assuming about 3.5 to 4 degrees of negative camber.
i didn't roll the rears its cut out just as much as a nice roll ... so i'm sure a +10 will still work out just nice but i my just stick with +15 that way i can add come camber in the rear .. so thanks for that info. you helped me out a lot for my next rear set up .....

think i can do a +10 an a 225/35 with this or is it pushing it .. pic of the rears cut
 
Reply
Old Jul 4, 2010 | 08:54 PM
  #1041  
CandlestickPark's Avatar
ill Sedan
Staff Alumni
iTrader: (87)
Joined: Jun 2007
Posts: 23,261
Likes: 2,688
From: Long Beach, SoCal
Premier Member

Originally Posted by g35snoop
ok well lets just say right now i'm at 2.5'' drop on springs and i'm at -3º but once i get the coils on the car i want to drop 3''. i'm sure ill be close or around -3.2º with a 225/35 rear. what would be your highly educated guess of a offset
I would say 9.5+10, but it really depending on where you camber ends up and how big or small your tires run. Sounds like you will be running less camber than I am, but you'll have 5mm more clearance based on your tire size. I would test fit +10 first then get a smaller spacer it rubs. You definitely don't want to rub with cut fenders, it will chew your tires up.
 
Reply
Old Jul 4, 2010 | 08:58 PM
  #1042  
SN00P's Avatar
CLUB MODERATOR
iTrader: (21)
Joined: Jan 2010
Posts: 8,028
Likes: 118
From: Florida G club
Originally Posted by CandlestickPark
I would say 9.5+10, but it really depending on where you camber ends up and how big or small your tires run. Sounds like you will be running less camber than I am, but you'll have 5mm more clearance based on your tire size. I would test fit +10 first then get a smaller spacer it rubs. You definitely don't want to rub with cut fenders, it will chew your tires up.
yea ill just test fit it .... i may just end up doing +15 at around -3º and adjust the camber .. -3.5º_ -4º will eat thru some tires and i drive around 25 miles to and from work a day
 
Reply
Old Jul 4, 2010 | 09:48 PM
  #1043  
FlyingLumpia's Avatar
Registered User
iTrader: (7)
Joined: Jul 2006
Posts: 3,284
Likes: 39
From: Washington State
I just went out to the garage and took some pics. Here you go.


 
Reply
Old Jul 4, 2010 | 10:08 PM
  #1044  
04G35NYC's Avatar
Registered User
iTrader: (17)
Joined: Jun 2006
Posts: 4,842
Likes: 78
From: Brooklyn,NY
^ Looks SICK.
 
Reply
Old Jul 4, 2010 | 10:22 PM
  #1045  
SN00P's Avatar
CLUB MODERATOR
iTrader: (21)
Joined: Jan 2010
Posts: 8,028
Likes: 118
From: Florida G club
^^^ wow very nice .. its perfect are your fronts pulled at all or just your rear ??
 
Reply
Old Jul 4, 2010 | 10:30 PM
  #1046  
FlyingLumpia's Avatar
Registered User
iTrader: (7)
Joined: Jul 2006
Posts: 3,284
Likes: 39
From: Washington State
fronts are not pulled and the rears are just rolled.
 
Reply
Old Jul 4, 2010 | 10:37 PM
  #1047  
SN00P's Avatar
CLUB MODERATOR
iTrader: (21)
Joined: Jan 2010
Posts: 8,028
Likes: 118
From: Florida G club
my fault miss read your other post ...with the tires on your wheel do you have a little stretch at all .. i was talking to levon before about a 225/35 and a 235/35 but i forgot now what he told me ..
 
Reply
Old Jul 5, 2010 | 01:13 AM
  #1048  
CandlestickPark's Avatar
ill Sedan
Staff Alumni
iTrader: (87)
Joined: Jun 2007
Posts: 23,261
Likes: 2,688
From: Long Beach, SoCal
Premier Member

Looks perfect Ernie!
 
Reply
Old Jul 5, 2010 | 01:16 AM
  #1049  
ttrank's Avatar
Grocery getter
iTrader: (57)
Joined: Jul 2005
Posts: 27,305
Likes: 190
From: Phoenix
Premier Member

Wow, don't hit any bumps when you are turning!
 
Reply
Old Jul 5, 2010 | 01:19 AM
  #1050  
4DGS's Avatar
Registered User
iTrader: (69)
Joined: Nov 2008
Posts: 14,524
Likes: 981
From: Ontario, Canada
I'm still working on my fitment, my tires are so stretched it looks like I have fender gaps from weird angles lol

I daily my car, so does cliff I'm pretty sure and we're low. Com'on join the DDL club (dailydrivenlow)
 
Reply


You have already rated this thread Rating: Thread Rating: 7 votes, 5.00 average.


All times are GMT -4. The time now is 07:18 AM.