Rear Strut Tower Bar Teaser
#421
04-05-2009, 09:46 PM
#423
04-06-2009, 12:28 AM
#425
04-12-2009, 05:26 AM
Originally Posted by RareJDM
Going to eat dinner then I'll post the pics.
Last edited by psedog; 04-12-2009 at 06:20 AM. Reason: Fixed a quote
#428
04-12-2009, 06:35 AM
Alright, the bar is installed. 
One of the holes on the car is bigger than the bolt. So it had a lot of wiggle room. So, I first installed the brackets snug, but not tightened down. Then when I got the bar in, I tightened up the bolts holding the bracket in.
I haven't taken the car out yet for a test drive. I'll do that in the morning on my way to work.
As you can see, it is level :P
My amp on the other hand isn't. Now I need to make a bracket for my cap. I have had it installed with Velcro for a while now. Mainly because I didn't want to put any holes in the carpet
. Now all bets are off
One of the holes on the car is bigger than the bolt. So it had a lot of wiggle room. So, I first installed the brackets snug, but not tightened down. Then when I got the bar in, I tightened up the bolts holding the bracket in.
I haven't taken the car out yet for a test drive. I'll do that in the morning on my way to work.
As you can see, it is level :P
My amp on the other hand isn't. Now I need to make a bracket for my cap. I have had it installed with Velcro for a while now. Mainly because I didn't want to put any holes in the carpet
. Now all bets are off
#429
04-12-2009, 09:58 AM
Excellent D.I.Y.!
Installed correctly and looks very NICE ! Great Job!
Each Mounting Bracket should be installed with the two Mounting Screws (Coupe towards the rear, Sedan towards the front), tightened just enough to hold the Bracket in place. Then, while pushing the Bracket up against the Inner Shock Tower Enclosure, tighten the two Bracket Mounting Screws. After tightening the Screws, a small "gap" may appear between the Bracket and the Inner Shock Tower Enclosure. This "gap" will disappear when adjusting the Bar. Adjust the Bar until Brackets become "snug" and no movement occurs.
CAUTION: DO "NOT" OVERTIGHTEN THE BAR!!
Lastly, tighten (snug) all remaining Hardware and your off!
Installed correctly and looks very NICE ! Great Job!
Each Mounting Bracket should be installed with the two Mounting Screws (Coupe towards the rear, Sedan towards the front), tightened just enough to hold the Bracket in place. Then, while pushing the Bracket up against the Inner Shock Tower Enclosure, tighten the two Bracket Mounting Screws. After tightening the Screws, a small "gap" may appear between the Bracket and the Inner Shock Tower Enclosure. This "gap" will disappear when adjusting the Bar. Adjust the Bar until Brackets become "snug" and no movement occurs.
CAUTION: DO "NOT" OVERTIGHTEN THE BAR!!
Lastly, tighten (snug) all remaining Hardware and your off!
Last edited by OH6 G35; 04-12-2009 at 10:13 AM.
#431
04-12-2009, 10:50 AM
#433
04-15-2009, 01:53 PM
#434
04-15-2009, 01:59 PM
)
#435
04-19-2009, 10:21 PM
I’m Finally A$$ Planted!
Rare JDM Sedan Rear Stabilizer Bar
Nice bar Zack (zackt69) & Dave (OH6 G35) ~ great quality! Thanks for the install help Darren (SouthbayGSedan)
I got the bar a few weeks ago in a hardy very much ready to ship box (plenty of packing material to protect)… it has taken a while to install because I wanted to black chrome plate the bar & hardware and powder coat the brackets a different color – it didn’t turn out quite as expected and some stuff had to be re-done – the bar looks a little chromier than when first received for some reason, it’s not quite a black as I’d like, but its decent – the pics below aren’t really indicative of what it looks like in person (especially the brackets) – but I’m not Marcus or Grant
~ anyway, that’s why it has taken so long to install.
As for performance… unfortunately I don’t drive the car much these days so it’s very hard to give fair evaluation of suspension stuff (I still don’t know how I feel about springs installed about 2 months ago because I’ve only driven the car twice since then)… but on my semi-spirited drive home from Darren’s; the rear end did seem very well planted. I didn’t push hard corners too much (yet) but it does feel tight and stable. Once I have a chance to try and swing the @ss around and get a real feel I’ll post better driving impression – but that might be a long time from now so I figured I’d at least give my prelim thoughts and post some pics.
If your car likes to shake it’s @ss like some hot chick at spring break this bar is not for you… but if you’re trying to rid the flex and squirrelly characteristics sometimes exhibited by the sedan – from what I can tell so far, this bar is a step in the right direction.
Nice bar Zack (zackt69) & Dave (OH6 G35) ~ great quality! Thanks for the install help Darren (SouthbayGSedan)
I got the bar a few weeks ago in a hardy very much ready to ship box (plenty of packing material to protect)… it has taken a while to install because I wanted to black chrome plate the bar & hardware and powder coat the brackets a different color – it didn’t turn out quite as expected and some stuff had to be re-done – the bar looks a little chromier than when first received for some reason, it’s not quite a black as I’d like, but its decent – the pics below aren’t really indicative of what it looks like in person (especially the brackets) – but I’m not Marcus or Grant
~ anyway, that’s why it has taken so long to install.
As for performance… unfortunately I don’t drive the car much these days so it’s very hard to give fair evaluation of suspension stuff (I still don’t know how I feel about springs installed about 2 months ago because I’ve only driven the car twice since then)… but on my semi-spirited drive home from Darren’s; the rear end did seem very well planted. I didn’t push hard corners too much (yet) but it does feel tight and stable. Once I have a chance to try and swing the @ss around and get a real feel I’ll post better driving impression – but that might be a long time from now so I figured I’d at least give my prelim thoughts and post some pics.
If your car likes to shake it’s @ss like some hot chick at spring break this bar is not for you… but if you’re trying to rid the flex and squirrelly characteristics sometimes exhibited by the sedan – from what I can tell so far, this bar is a step in the right direction.
This post is also in the Suspension section
https://g35driver.com/forums/brakes-...ml#post4135619
and Sedan section
https://g35driver.com/forums/g35-sed...m-planted.html